M800 Gas Flow Computer - Spirax Sarco

More documents

Recommendations

Info

6.7.2.2 Optional 4-20 mA pressure output Commissioning mode • Outputs • 4-20 mA Commissioning mode • Outputs • 4-20 mA Pres Commissioning mode • Outputs • 4-20 mA Pres • Set 4 mA Commissioning mode • Outputs • 4-20 mA Pres • Set 4 mA 000.00 ok Enter pressure (bar g or psi g) Commissioning mode • Outputs • 4-20 mA Pres • Set 20 mA Commissioning mode • Outputs • 4-20 mA Pres • Set 20 mA 3.00 ok Enter pressure (bar g or psi g) Commissioning mode • Outputs • 4-20 mA Pres • Check 4 mA Commissioning mode • Outputs • 4-20 mA Pres • Check 4 mA op = 4 mA ok Commissioning mode • Outputs • 4-20 mA Pres • Check 20 mA Commissioning mode • Outputs • 4-20 mA Pres • Check 20 mA op = 20 mA ok After the data has been entered, exit the 4-20 mA output sub-menu by pressing . The menu will then step to Pulse output (see Section 6.7.3). 54 IM-P333-25 MI Issue 2
6.7.3 Pulse output This sub-menu allows the pulsed output to be configured. The pulse output is a volt free digital pulse output R≥10 KΩ, Maximum voltage 28 Vdc. No/Pulse This allows the total volume, which is equivalent to one pulse to be configured. Units are dependent on the Unit setting. Pulse width This allows the width of the pulse to be set. The width can be set in 0.01 second increments from 0.02 seconds to a maximum of 0.2 seconds. Commissioning mode • Outputs • Pulse Commissioning mode • Outputs • Pulse • No/pulse Commissioning mode • Outputs • Pulse • No/pulse 0001 ok Commissioning mode • Outputs • Pulse • Width S Commissioning mode • Outputs • Pulse • Width S 0.02 ok After the data has been entered, exit the Pulse output sub-menu by pressing . The menu will then step to Comms output (see Section 6.7.4). IM-P333-25 MI Issue 2 55
Page 1 and 2:
3330951/ 2 IM-P333-25 MI Issue 2 M8
Page 3 and 4: The symbols, used on the product an
Page 5 and 6: 1.11 Permits to work All work must
Page 7 and 8: 3. System overview 3.1 Orifice plat
Page 9 and 10: 3.3 Gilflo ILVA mechanical installa
Page 11 and 12: 3.5 4 - 20 mA linear device mechani
Page 13 and 14: 4.1 Wall mounted version h Fig. 7 F
Page 15 and 16: h b Fig. 12 a h c 3. Unclip the hi
Page 17 and 18: Fitting of option boards 1. Isolate
Page 19 and 20: 5.2 Important - Please read the fol
Page 21 and 22: 5.4 Wiring diagram - Vortex flowmet
Page 23 and 24: 5.6 Wiring diagram - Pulsed output
Page 25 and 26: RS485 option board Additional notes
Page 27 and 28: Master 1200 m (4000 ft) -Tx Tx T Rt
Page 29 and 30: Run mode data sequence 20290 Nm³
Page 31 and 32: 6.3 Commissioning mode The commissi
Page 33 and 34: Continued from page 32 Commissionin
Page 35 and 36: Commissioning mode • Basic Data C
Page 37 and 38: 6.5.1 Commissioning sequence for th
Page 41 and 42: To page 40 Continued from page 40 C
Page 43 and 44: Table 2 Specific gas dynamic viscos
Page 47 and 48: 6.6.1 Temperature sensor menu. The
Page 49 and 50: 6.7 Outputs The Outputs sub-menu al
Page 51 and 52: Commissioning mode • Outputs •
Page 53: 6.7.2.1 Optional 4-20 mA temperatur
Page 57 and 58: Summary of the Modbus Protocol for
Page 59 and 60: 6.8 Test menu The test sub-menu all
Page 61 and 62: 6.8.3 Testing the 4-20 mA outputs T
Page 63 and 64: Continued from page 62 Commissionin
Page 65 and 66: 6.12 Clock This allows the time and
Page 67 and 68: To page 66 Continued from page 66
Page 69 and 70: 7. Fault finding WARNING: Before co
Page 71 and 72: Commissioning Error messages Error
Page 73 and 74: 8. Maintenance Note: Before actioni
Page 75 and 76: 9.7 Input technical data 4-20 mA in
Page 77 and 78: 9.10 Maximum and minimum programmab
Page 79 and 80: IM-P333-25 MI Issue 2 79
show all

M800 Gas Flow Computer - Spirax Sarco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?