Benutzerhandbuch / User Manual - TR Electronic

More documents

Recommendations

Info

Assembly Figure 2: Flange installation 4.1.2 Start-up torque of the shaft, in dependence of the temperature Temperature [°C] Radius [cm] Force [N] Start-up torque [Ncm] 25 1.5 0.5 0.75 -20 1.5 1.5 2.25 -40 1.5 6.7 10.05 Figure 3: Start-up torque Printed in the Federal Republic of Germany © TR-Electronic GmbH 2010, All Rights Reserved 05/25/2011 TR - ECE - BA - DGB - 0079 - 03 Page 127 of 207
Assembly 4.2 Hollow shaft version CDH-75 4.2.1 Requirements ● Danger of death, serious physical injury and/or damage to property due to deactivation of safety functions, caused by an unstable shaft drive! ‣ The system manufacturer must implement suitable design measures, so that the drive of the measuring system is ensured at all times through the shaft and mounting of the measuring system (fault exclusion). The specifications of DIN EN 61800-5-2:2008 "Adjustable speed electrical power drive systems, Safety requirements - Functional, Table D.16 – Motion and position sensors" must be observed. ‣ In general, the requirements and acceptance conditions for the complete system must be taken into account for mounting. As the installation situation is application-dependent, the following notes are not exhaustive. ‣ The measuring system must be installed on a grease-free shaft. ‣ Axial slipping of the measuring system on the drive shaft must be prevented by the fixing of the clamping ring, see Figure 4. ‣ Further measures may be required to prevent axial slipping of the measuring system. ‣ The clamping of the measuring system must not be axially loaded. ‣ The screw of the clamping ring must be tightened with 3 Nm using a torque wrench. ‣ The screw must be secured against unintentional loosening. ‣ Radial slipping of the measuring system on the drive shaft must be prevented by means of form closure, using a parallel key / groove combination; the measuring system must be fixed on the side of the drive using a dowel pin, see Figure 5. ‣ In case of applications with low ambient temperatures, increased values for the start-up torque result. This fact is to be considered when the assembling and wave drive is performed. © TR-Electronic GmbH 2010, All Rights Reserved Printed in the Federal Republic of Germany Page 128 of 207 TR - ECE - BA - DGB - 0079 - 03 05/25/2011
Page 1 and 2: Rotary Encoders Linear Encoders Mot
Page 3 and 4: TR-Electronic GmbH D-78647 Trossing
Page 5 and 6: Contents 5.6 SIN/COS interface / In
Page 7 and 8: Contents 11 Troubleshooting and Dia
Page 9 and 10: General information 1 General infor
Page 11 and 12: General information 1.3 General fun
Page 13 and 14: General information 1.4 Overview of
Page 15 and 16: Basic safety instructions 2.2 Gener
Page 17 and 18: Basic safety instructions 2.4 Safet
Page 19 and 20: Basic safety instructions 2.6 Organ
Page 21 and 22: Basic safety instructions ● The m
Page 23: Assembly 4 Assembly 4.1 Solid shaft
Page 27 and 28: Assembly Figure 5: Form closure Fig
Page 29 and 30: Installation / Preparation for Comm
Page 37 and 38: PROFIBUS / PROFIsafe - Commissionin
Page 57 and 58: Parameter Definition / CRC Calculat
Page 59 and 60: Safety Program Creation - Configura
Page 75 and 76:
Safety Program Creation - Configura
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Access to the safety-oriented data
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Preset Adjustment Function 10.1 Pro
Page 89 and 90:
Troubleshooting and Diagnosis Optio
Page 91 and 92:
Troubleshooting and Diagnosis Optio
Page 93 and 94:
Replacing the Measuring System 12 R
Page 95 and 96:
Checklist Continued Sub-item To not
Page 97 and 98:
Technical Data 14.2.2 Device-specif
Page 99 and 100:
Appendix 15 Appendix 15.1 Abbreviat
Page 101 and 102:
Appendix 15.2 TÜV certificate © T
Page 103 and 104:
Appendix 15.4 Accessories 490-00101
show all

Benutzerhandbuch / User Manual - TR Electronic

Create successful ePaper yourself

Delete template?

Save as template?