Flo-Ware Manual - Hachflow

More documents

Recommendations

Info

Operation • Interpolate over blank cells: click and drag to highlight data from above the first empty data cell to below the last empty data cell. Select Edit > Interpolate. The table is updated with the linear interpolated data. The start and end cells are used as reference points. • Change to the Scatter Plot view and click in the scatter plot where the data should likely be (refer to Use the scatter plot on page 18). 10. Select a span of inaccurate data in the chart. First, left-click the start of the data, then right-click the end of the inaccurate data span. The selected data for both themes will change color. Make sure that the selected span includes the data to be reconstructed. Note: If the Pan or Zoom buttons are enabled, the data cannot be selected. 11. In the Data Reconstruct panel, select Table > Reconstruct. The theme is updated to show the correction (Figure 3). 12. Select Table > Save to save the table. Enter a file name and location to store the file. Note: This table can be used for future data reconstruction at the same site. 13. Close the Data Reconstruct panel to exit the reconstruction session. Figure 3 Data before and after reconstruction Note: To reverse the reconstruction, select the Raw Data view and click the undo button. 1 Valid data 2 Incorrect data 3 Repaired data 3.6.3 Use the scatter plot Use the scatter plot when it is necessary to reconstruct the entire set of data. First, select a span of accurate data with the line chart to populate the reconstruction table. Then change to the scatter plot view to reconstruct the data. 1. Complete 1 to 9 to in Use a reconstruction table on page 17. 2. Click on the SCATTER PLOT button. The data from the reconstruction table is shown in the scatter plot in a different color from the rest of the data set (Figure 4). 3. If necessary, edit the data in the reconstruction table. The data points on the scatter plot are updated to show the new values. 4. In the Data Reconstruct panel, select Table > Reconstruct. The entire set of data is updated to match the table data (Figure 4). 5. Save the reconstruction file and close the Data Reconstruct panel. Note: To reverse the reconstruction, select the Raw Data view and click the UNDO button. 18
Operation Figure 4 Data before and after reconstruction 19
Page 1: DOC026.53.80112 Flo-Ware 4 Software
Page 4 and 5: Table of Contents 4.1.4.3 Communica
Page 6 and 7: General information Table 1 Instrum
Page 8 and 9: Installation 6
Page 10 and 11: Operation 3.2.1 Edit data Data can
Page 12 and 13: Operation Figure 2 Open file window
Page 14 and 15: Operation 3.2.3.4 Copy files to a n
Page 16 and 17: Operation different themes, select
Page 18 and 19: Operation 3.4.3 Print a chart A pap
Page 22 and 23: Operation 20
Page 24 and 25: Device communication Figure 5 Attac
Page 26 and 27: Device communication Figure 8 FL900
Page 28 and 29: Device communication 4.1.4 Make a l
Page 30 and 31: Device communication Option Baud Ra
Page 32 and 33: Device communication a. Click on th
Page 34 and 35: Device communication Option Distanc
Page 36 and 37: Device communication 7. Click TAKE
Page 38 and 39: Device communication The velocity c
Page 40 and 41: Device communication Note: Only the
Page 42 and 43: Device communication 11. Optional:
Page 44 and 45: Device communication Note: The Cali
Page 46 and 47: Device communication Option Analyze
Page 48 and 49: Device communication e. Select the
Page 50 and 51: Device communication Option Export
Page 52 and 53: Device communication 4.1.6 Troubles
Page 54 and 55: Device communication • 7 bits, od
Page 56 and 57: Device communication capable of aut
Page 58 and 59: Device communication Returned value
Page 60 and 61: Device communication Table 9 Base u
Page 62 and 63: Device communication Table 9 Base u
Page 64: Device communication 62

Flo-Ware Manual - Hachflow

Create successful ePaper yourself

Delete template?

Save as template?