ER-A520/ER-A530 INSTRUCTION MANUAL

More documents

Recommendations

Info

Job-Code-Based Programming This section illustrates how to program items using job codes. Using job codes allows you to program a wide variety of items in comparison with direct programming. Start this programming by entering a corresponding job code as shown below. 2110 . @ All the items which can be programmed by the job-code-based programming are listed on this page and the following, and those which can also be programmed by the direct programming are marked with the symbol “ Direct ” that follows job codes. 1 Setting the date and time Setting the date PGM 2 2610 Direct Enter the month (one or two digits), day (two digits), and year (four digits: 2000 – 2099) in this sequence. Procedure 2610 Date (seven or eight digits) . @ Ç Example Key operation 2610 .@ 08262004 Ç Print Date Setting the time PGM 2 2611 Direct Set the time using the military time (24-hour) system. For example, when the time is set to 2:30 AM, enter 230; and when it is set to 2:30 PM, enter 1430. The time is printed and displayed on the real time system. Procedure 2611 Time (max. four digits) . @ Ç Example Key operation 2611 .@ 1430 Ç Print Time 96
2 Setting the register and consecutive numbers Setting the register number When your store has two or more registers, it is practical to set separate register numbers for their identification. You may set them with a maximum of six digits. Procedure PGM 2 To set the register number “0” 2612 Register number 2612 . @ (one to six digits) Ç Example To set the register number as “123456” Key operation 2612 .@ 123456 Ç Print Register number Setting the consecutive number The consecutive number is increased by one each time a receipt is issued. Enter a number (one to four digits) that is one less than the desired starting number. Procedure . @ PGM 2 2613 To begin the count from 0001 Ç 2613 A number (one to four digits) that is one less than the desired starting number Example Setting the count start number as “1001” Key operation 2613 .@ 1000 Ç Print Consecutive number 97
Page 1 and 2:
ELECTRONIC CASH REGISTER INSTRUCTIO
Page 3 and 4:
INTRODUCTION Thank you very much fo
Page 5 and 6:
Taxable subtotal ·········
Page 7 and 8:
Functional programming 2 (#2111) ·
Page 9 and 10:
Closed GLU/PBLU report ······
Page 11 and 12:
EXTERNAL VIEW OF THE ER-A530A Front
Page 13 and 14:
KEYBOARD 1 ER-A520A standard keyboa
Page 15 and 16:
NO DEL No delete key C NEXT Condime
Page 17 and 18:
LEVEL # PLU level shift number key
Page 19 and 20:
KEYS AND SWITCHES 1 Mode switch and
Page 21 and 22:
DISPLAYS 1 Operator display The ope
Page 23 and 24:
Procedure ■ Sign-on Variant 1 : (
Page 25 and 26:
UPC entries Scan UPC code Ä UPC co
Page 27 and 28:
Successive multiplication entries T
Page 29 and 30:
Single item cash sale (SICS)/single
Page 31 and 32:
ii) Manual scale entries of refunde
Page 33 and 34:
Example Direct PLU1: PLU code 1 (PL
Page 35 and 36:
Example PLU price level 1: PLU 1 ($
Page 37 and 38:
Mix-and-match entries This function
Page 39 and 40:
UPC learning function When you ente
Page 41 and 42:
Example • Price change mode Key o
Page 43 and 44:
3 Finalization of transaction Cash
Page 45 and 46:
4 Food stamp calculations Food stam
Page 47 and 48: 5 Tax calculations Automatic tax Wh
Page 49 and 50: Tax status shift Your machine allow
Page 51 and 52: Example Key operation Print 111 n C
Page 53 and 54: Deposit entries Deposit refers to a
Page 55 and 56: Bill totalizing/bill transfer Bill
Page 57 and 58: Example One of the dept. 9 items is
Page 59 and 60: 7 Auxiliary entries Percent calcula
Page 61 and 62: Refund entries If a refund item is
Page 63 and 64: Gratuity Calculation When the payme
Page 65 and 66: Tip editing This function is used f
Page 67 and 68: Received on account entries Procedu
Page 69 and 70: 10 WASTE mode This mode is used to
Page 71 and 72: 3 Subtotal void You can void an ent
Page 73 and 74: OVERRIDE ENTRIES Programmed limits
Page 75 and 76: SPECIAL PRINTING FUNCTIONS 1 Copy r
Page 77 and 78: 5 Printing of header and footer gra
Page 79 and 80: FOR THE MANAGER PRIOR TO PROGRAMMIN
Page 81 and 82: 79 Alphanumeric character code tabl
Page 83 and 84: Time Set the time using the militar
Page 85 and 86: Note Group number You can assign a
Page 87 and 88: Functional selection PGM 2 Procedur
Page 89 and 90: 4 Programming for discount keys (-)
Page 91 and 92: Functional programming PGM 2 Proced
Page 93 and 94: Programming for the Ç, Å, ', and
Page 95 and 96: 9 Programming for the automatic tax
Page 97: • If the tax is not provided for
Page 101 and 102: Procedure One- or two-*digit number
Page 103 and 104: Example Programming the tax rate 4%
Page 105 and 106: Procedure 2110 Dept. code *ABCDEF .
Page 107 and 108: A limit amount (HALO) of entry You
Page 109 and 110: Group number You can assign departm
Page 111 and 112: Department key positioning PGM 2 Yo
Page 113 and 114: Sign (+/-) The function of every PL
Page 115 and 116: Unit prices PGM 1 PGM 2 1210 Direct
Page 117 and 118: * Item: Selection: Entry: A Delete
Page 119 and 120: Example Programming ABCDEF=010001 f
Page 121 and 122: Commission groups PGM 2 2215 2235 D
Page 123 and 124: Age limitation PGM 2 2280 2236 2081
Page 125 and 126: Adding the stock quantity Example T
Page 127 and 128: Example Programming mix-and-match t
Page 129 and 130: Assigning PLUs for condiment entry
Page 131 and 132: Programming Non-PLU code format PGM
Page 133 and 134: Example Programming of PLU 1 (level
Page 135 and 136: 6 Programming for miscellaneous key
Page 137 and 138: Example Programming “Ÿ” for th
Page 139 and 140: Percent entry type (%) PGM 2 2310 Y
Page 141 and 142: Vendor or store coupon selection (-
Page 143 and 144: *2: Item: Selection: Entry: A GLU/P
Page 145 and 146: High amount lockout (HALO) for chec
Page 147 and 148: CAT programming When you use a cred
Page 149 and 150:
Function no. Key or function In def
Page 151 and 152:
Function no. Key or function In def
Page 153 and 154:
Functional programming Procedure PG
Page 155 and 156:
Available mode for PLU level shift
Page 157 and 158:
**P: 3 * Item: Selection: Entry: A
Page 159 and 160:
**P: 11 (ABCDEFGH: Always enter 0.)
Page 161 and 162:
Programming of logo messages Your r
Page 163 and 164:
Setting the time range for hourly r
Page 165 and 166:
Functional programming for the prin
Page 167 and 168:
Validation message You can program
Page 169 and 170:
Example Assigning channel 1 to the
Page 171 and 172:
Remote printer name Procedure PGM 2
Page 173 and 174:
RS-232C interface PGM 2 6110 6111 6
Page 175 and 176:
Programming the CAT interface 7116
Page 177 and 178:
Secret codes to control access to t
Page 179 and 180:
11 TRAINING mode The training mode
Page 181 and 182:
Program for: Mode switch position J
Page 183 and 184:
3 Reading of programmed key nos. fo
Page 185 and 186:
13 Reading of programmed items for
Page 187 and 188:
14 Reading of programmed items for
Page 189 and 190:
16 Reading of programmed tax tables
Page 191 and 192:
EAN-13 • Ordinary EAN-13 code (us
Page 193 and 194:
Item Mode switch position X1/Z1 X2/
Page 195 and 196:
Item Dynamic UPC report by associat
Page 197 and 198:
2 Daily sales totals General report
Page 199 and 200:
Item 1 counter and total Item 1 tot
Page 201 and 202:
Cashier/Server report Using this fu
Page 203 and 204:
Full department report Individual g
Page 205 and 206:
UPC code UPC total for price level
Page 207 and 208:
PLU/UPC zero sales report by depart
Page 209 and 210:
Closed GLU/PBLU report • Sample X
Page 211 and 212:
Transaction report Cash in drawer r
Page 213 and 214:
Deleting of non-accessed UPCs • S
Page 215 and 216:
COMPULSORY CASH/CHECK DECLARATION I
Page 217 and 218:
OPERATOR MAINTENANCE 1 In case of p
Page 219 and 220:
4 Installing and removing the paper
Page 221 and 222:
Removing the journal paper roll Are
Page 223 and 224:
5 Cleaning the print head When the
Page 225 and 226:
8 Before calling for service The ma
Page 227 and 228:
SPECIFICATIONS Model: ER-A520A/A530
show all

ER-A520/ER-A530 INSTRUCTION MANUAL

Create successful ePaper yourself

Delete template?

Save as template?