Download latest Tool Catalogue as PDF - DICTUM GmbH

Sculpting ToolsDue to sole manual production sweeps and widthsmay vary slightly.carving tOOl tYpeSgouges - Gouges are the classical sculptor’stools. Their curvature is described by sweepnumbers (from 2 = very flat to 11 = verystrongly curved).chisels - These have a cutting edge groundobliquely or at a right angle. By contrast withnormal wood working chisels, they are sharpenedon both sides. Due to their versatilityfor use with edges, contours, peripheries,surfaces and inscriptions, they are a must inevery basic set.v-parting tools - These have a V-shaped crosssectionand are used for cutting sharp-edgedgrooves, outlining patterns, and carving letters.aSweep Blade width9 5 mm no. 701442 19.08 € 22.70 €10 mm no. 701443 20.08 € 23.90 €16 mm no. 701444 23.11 € 27.50 €20 mm no. 701445 25.88 € 30.80 €26 mm no. 701446 26.72 € 31.80 €10 5 mm no. 701447 19.08 € 22.70 €10 mm no. 701448 20.08 € 23.90 €16 mm no. 701449 23.11 € 27.50 €20 mm no. 701450 25.88 € 30.80 €26 mm no. 701451 26.72 € 31.80 €11 2 mm no. 701452 20.42 € 24.30 €6 mm no. 701453 20.42 € 24.30 €10 mm no. 701454 22.02 € 26.20 €16 mm no. 701455 24.54 € 29.20 €aCARVING TOOL, GOUGE, LONG BENTThe long bent form is used in curved recesses to allow you to cut out ofthe piece from the deepest point without damaging the edges of recess.Blade length 110 – 150 mm, Overall length 220 – 280 mmSatisfactionSweep Blade width17 equals 8 13 mm no. 701456 22.02 € 26.20 €20 mm no. 701457 27.14 € 32.30 €26 mm no. 701458 28.49 € 33.90 €Guaranteecranked tools - Curved or cropped tools areadvantageous for elaborating concave surfaces,recesses or relief backgrounds. Thenarrower the work situation, the greater thetools cropping required.B18 equals 9 10 mm no. 701459 22.02 € 26.20 €16 mm no. 701460 27.48 € 32.70 €carving tool Sets Price advantage!Sets of selected sculptor‘s gouges with highqualityleather tool roll of fine cowhide.BCARVING TOOL, GOUGE, SHORT BENTSimilar to the long bent form, these gouges are also used for deep, curved shapes.The even stronger bent of the gouge allows you to carve transitions in even deeperareas and to create small radiuses and arches.Blade length 110 – 150 mm, Overall length 220 – 280 mmSatisfactionSweep Blade width29 equals 8 10 mm no. 701461 19.83 € 23.60 €13 mm no. 701462 20.08 € 23.90 €Guarantee30 equals 9 10 mm no. 701463 19.83 € 23.60 €16 mm no. 701464 24.29 € 28.90 €26 mm no. 701465 31.60 € 37.60 €ccCARVING TOOL, V-PARTING TOOLV-parting tools are popularly used in relief carving to delimit areas.Another important use is the cutting of even grooves.Blade length 110 – 150 mm, Overall length 220 – 280 mmSatisfactionGuaranteeddCARVING TOOLS, 6-PIECE SET6 piece set as basis equipment for beginners.Flat/skew 13 mm; V-parting tool 41 V 65° / 10 mm;gouges, straight sweep 5 / 20 mm; sweep 6 / 13 mm;sweep 8 / 10 mm; sweep 10 / 5 mm.no. 701480 133.61 € 159.00 €CARVING TOOLS, 12-PIECE SETWith these 12 sculptor‘s tools you are perfectlyequipped for sculpting figures and ornaments. Flat 10 mm;flat/skew 10 mm; V-parting tool 41 V 65° / 6 mm; gouges,straight sweep 6 / 10 and 20 mm; sweep 8 / 5 and 13 mm;sweep 9 / 5 and 10 mm; sweep 11/ 6 mm; gouge,short cranked sweep 9 / 10 mm; gouge,long cranked sweep 8 / 20 mm.no. 701481 257.14 € 306.00 €SatisfactionGuaranteeSatisfactionGuaranteeSweep Blade width41 V 65° 3 mm no. 701466 21.51 € 25.60 €41 V 65° 6 mm no. 701467 21.76 € 25.90 €41 V 65° 10 mm no. 701468 24.29 € 28.90 €45 V 95° 10 mm no. 701469 24.29 € 28.90 €winged V-Parting Tool47 6 mm no. 701470 30.42 € 36.20 €dictUM satisfaction guaranteeProducts can be testedfor 15 days.(For more information see page 3)Inclusive free sharpening pass.For more information see page 3.Two free sharpeningsSatisfactionGuaranteeOrder hotline: Phone: +49-(0)991-9109-902 or +49-(0)1805-9109-902* • www.more-than-tools.de 47