Complete (13 MB) - Chris Alston's Chassisworks

More documents

Recommendations

Info

After the application of another dab of antiseize,the rod ends are threaded into theA-arms, until the jam nuts are snug againstthe arm itself.This step must be done carefully becausethe upper and lower A-arm mounts arethreaded and welded to the frame. Use the5/8-18 tap to chase the threads on the frontand backsides of both upper mounts. Blowany remaining particles out of the hole withan air hose.#917701 Page 11
Page 1: READ ALL INSTRUCTIONS COMPLETELY AN
Page 5 and 6: DISCLAIMER OF WARRANTYPurchasers re
Page 7 and 8: Installing SuspensionIn this sectio
Page 9 and 10: The balljoint is then screwed into
Page 11: Thread the balljoint in as far as p
Page 17: Next, install the shock simulator a
Page 21 and 22: Installing Steering RackMounting th
Page 25 and 26: Next, turn the rack all the way to
Page 29 and 30: The adjustment for both caster andc
Page 31 and 32: If rotating the tie rod end 360 deg
Page 33 and 34: Grease the tie rod end with a small
Page 35 and 36: To prevent the urethane bushingsfro
Page 37 and 38: Slide the billet aluminum cap over
Page 39 and 40: Insert the lower bushing assembly i
Page 41 and 42: Screw the spring seat adjuster onto
Page 43 and 44: Install the lower shock spud first.
Page 45 and 46: Add a drop of Loctite to the thread
Page 47 and 48: Pack the outer wheel bearing as you
Page 49 and 50: Next, install the Wilwood brake cal
Page 51 and 52: Use a 3/8” wrench to tighten the
Page 53 and 54: Move the spindle to full right lock
Page 55 and 56: Insert one urethane bushing into ea
Page 57 and 58: These optional stainless steel "spu
Page 59 and 60: Installing Manual Transmission,Clut
Page 61 and 62: Item 5916-F10-01 4-Speed, Powerglid
Page 63 and 64:
After you remove the engine, place
Page 65 and 66:
Use vise grip pliers and an end wre
Page 67 and 68:
Disconnect the clamps that attach t
Page 69 and 70:
Remove the bolts that attach the en
Page 71 and 72:
You need three people; one to opera
Page 73 and 74:
Lower the clip to the ground and pu
Page 75 and 76:
This is the correct orientation of
Page 77 and 78:
Place the top part of the mid and r
Page 79 and 80:
Install the lower half of the rear
Page 81 and 82:
Measure from the lip on the rocker
Page 83 and 84:
Attach the stock hook rod to the pa
Page 85 and 86:
Install two 1/2” self-locking set
Page 87 and 88:
Slide the splined end of the u-join
Page 89 and 90:
This is a photo of the completed in
Page 91 and 92:
Drill a 1/8” hole centered in the
Page 93 and 94:
Drill the remaining rivet holes sta
Page 95 and 96:
Installing HeadersSpecial Note: We
Page 97 and 98:
Installing SubframeConnectorsThe su
Page 99 and 100:
Once you have all the bolts removed
Page 101 and 102:
The spring clips can be just as tri
Page 103 and 104:
Slide a 3/8 inch flat washer over t
Page 105 and 106:
#917701 Page 104
show all

Complete (13 MB) - Chris Alston's Chassisworks

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?