MY1 Mechanically Jointed Rodless Cylinder

Mechanically Jointed Rodless CylinderSlide Bearing Guide TypeSeries MY1M39Stroke Adjusting Unit SpecificationsBore size (mm)Unit symbolConfigurationShock absorber modelFine stroke adjustment range (mm)Stroke adjustment rangeJIS Symbol16 20A L A LShock Absorber SpecificationsModelMax. energy absorption (J)Stroke absorption (mm)Max. collision speed (mm/s)Max. operating frequency (cycle/min)Springforce (N)ExtendedRetractedOperating temperature range (°C)WithadjustingboltSpecificationsHBore size (mm)AFront/Side portBottom port25LH16 20 25 32 40 50 63AirDouble acting0.15 to 0.8 MPa1.2 MPa5 to 60°CAir cushionNon-lube1000 or less +1.80+1.8+2.81001 to 3000 +2.82700 or less 0 , 2701 to 5000 00M5 x 0.8Rc 1/8 Rc 1/4 Rc 3/8A32L0 to –5.6 0 to –6 0 to –11.5 0 to –12 0 to –160 to –20 0 to –25When exceeding the stroke fine adjustment range: Utilize a made-to-order specifications “-X416” and “-X417”.RB08062.96801.964.22RB0806withadjustingboltWithadjustingboltRB10075.97704.226.86RB0806withadjustingboltRB141219.6121500456.8615.985 to 60FluidActionOperating pressure rangeProof pressureAmbient and fluid temperatureCushionLubricationStroke length tolerancePipingportsizeRB1007withadjustingboltWithadjustingboltRB201558.815258.3420.50RB1007withadjustingboltRB272514725108.8320.01RB1412withadjustingboltWithadjustingboltRB1412withadjustingboltø4HRB2015withadjustingboltAWithadjustingboltPiston Speed40LRB1412withadjustingboltø5HRB2015withadjustingboltAø6Withadjustingbolt50LRB2015withadjustingboltø8HRB2725withadjustingboltø10AWithadjustingbolt63LRB2015withadjustingboltø11Bore size (mm) 16 to 63Without stroke adjusting unit100 to 1000 mm/sStrokeadjusting unitA unitL unit and H unit100 to 1000 mm/s (1)100 to 1500 mm/s (2)Note 1) Be aware that when the stroke adjusting range is increased bymanipulating the adjusting bolt, the air cushion capacitydecreases. Also, when exceeding the air cushion stroke ranges onpage 8-11-43, the piston speed should be 100 to 200 mm persecond.Note 2) The piston speed is 100 to 1000 mm/s for centralized piping.Note 3) Use at a speed within the absorption capacity range. Refer topage 8-11-43.HRB2725withadjustingboltMXMTSMYCYMGCXD--X20-DataSymbol-XB11-XC18-XC67-X168-X416-X417Made to Order Specifications(For details, refer to page 8-31-1.)SpecificationsLong strokeNPT finish piping portNBR rubber lining in dust seal bandHelical insert thread specificationsHolder mounting bracket ΙHolder mounting bracket ΙΙStandard StrokeBore size(mm)1620, 25, 32, 4050, 63Standard stroke (mm) ∗100, 200, 300, 400, 500, 600, 700800, 900, 1000, 1200, 1400, 16001800, 2000Maximum manufacturable stroke(mm)∗ Strokes are manufacturable in 1 mm increments, up to the maximum stroke. However, whenexceeding a 2000 mm stroke, specify “-XB11” at the end of the model number.300050008-11-41