MY1 Mechanically Jointed Rodless Cylinder

More documents

Recommendations

Info

Series MY18PrecautionsBe sure to read before handling. For Safety Instructions and Actuator Precautions, refer to pages 8-34-3 to 8-34-6.MountingCaution1. Do not apply strong impacts orexcessive moment to the slidetable (slider).• The slide table (slider) is supported byprecision bearings (MY1C, MY1H) orresin bearings (MY1B, MY1M).Therefore, do not apply strongimpacts or excessive moment, etc.,when mounting workpieces.2. Align carefully when connectingto a load having an externalguide mechanism.• Mechanically jointed rodless cylinderscan be used with a direct load withinthe allowable range for each type ofguide. Please note that carefulalignment is necessary whenconnecting to a load having anexternal guide mechanism. As thestroke becomes longer, variations inthe center axis become larger.Consider using a connection method(floating mechanism) that is able toabsorb these variations. Furthermore,use the special floating brackets (referto page 8-11-28) which have beenprovided for Series MY1B.3. Do not use in an environmentwhere the cylinder is exposedto coolant, cutting oil, waterdrops, adhesive foreign particles,dust, etc. and avoid usewith compressed air containingdrainage and foreign particles.•Foreign matter or liquids on thecylinder , s interior or exterior can washout the lubricating grease, which canlead to deterioration and damage ofdust seal band and seal materials,causing a danger of malfunction.When operating in locations withexposure to water and oil, or in dustylocations, provide protection such as acover to prevent direct contact withthe cylinder, or mount so that the dustseal band surface faces downward,and operate with clean compressedair.Caution1. Do not unnecessarily alter theguide adjustment setting.• The adjustment of the guide is presetand does not require readjustmentunder normal operating conditions.Therefore, do not unnecessarily alterthe guide adjustment setting.However, series other than the MY1HSeries can be readjusted and theirbearings can be replaced.To perform these operations, refer tothe bearing replacement proceduregiven in the instruction manual.Caution1. Air leakage•Take precautions under operatingconditions in which negativepressure is increased inside thecylinder by external forces or inertialforces. Air leakage may occur due toseparation of the seal belt.8-11-8
Series MY1Specific Product PrecautionsBe sure to read before handling.9CautionCentralized Piping Port Variations• Head cover piping connection can be freely selected to best suit different piping conditions.Applicable bore sizePort variationsMXMY1B10MY1H10LRMTSMYCYMGLRLRCXD-Note 1)LRLRRLLRLNote 1)R-XNote 1) These ports are not applicable to MY1H10.MY1B16 to 100MY1M16 to 63MY1C16 to 63MY1H16 to 40LRLRLSlide table operating directionLRRLRLRLR20-DataLRRLNote 2) RRNote 2)LLO-ringLRPiping tubeSlide table operating directionNote 2) For bottom piping, refer to the figure above.MY1HT50/63RLLRLRLRLRSlide table operating direction8-11-9
Page 4 and 5: Series MY1Model SelectionFollowing
Page 6 and 7: Series MY1Model SelectionFollowing
Page 10 and 11: 8-11-1010
Page 12 and 13: Series MY1BBefore OperationMechanic
Page 14 and 15: Mechanically Jointed Rodless Cylind
Page 34 and 35: 34MY1MSeriesSlide Bearing Guide Typ
Page 36 and 37: Series MY1MModel SelectionFollowing
Page 40 and 41: Series MY1M40Theoretical Output(N)B
Page 42 and 43: Series MY1M42Cushion CapacityTighte
Page 44 and 45: Series MY1M44Standard Type/Centrali
Page 46 and 47: Series MY1M46Stroke Adjusting UnitW
Page 48 and 49: Series MY1M48Construction: ø16 to
Page 50 and 51: Series MY1CBefore OperationMechanic
Page 58 and 59:
Mechanically Jointed Rodless Cylind
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
64MY1HSeriesHigh Precision Guide Ty
Page 66 and 67:
Series MY1HModel SelectionFollowing
Page 68 and 69:
Page 70 and 71:
Series MY1H70Theoretical OutputBore
Page 72 and 73:
Series MY1H72With End LocksRecommen
Page 74 and 75:
Series MY1H74Cushion CapacityTighte
Page 76 and 77:
Series MY1H76Standard Type/Centrali
Page 78 and 79:
Series MY1H78Stroke Adjusting UnitW
Page 80 and 81:
Series MY1H80Side SupportSide suppo
Page 82 and 83:
Series MY1H82Construction: ø16 to
Page 84 and 85:
8-11-8884
Page 86 and 87:
Series MY1HTBefore OperationMechani
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Series MY1Auto Switch96D-A90(V), D-
Page 98 and 99:
Auto Switch Series MY198Proper Auto
Page 100 and 101:
Auto Switch Series MY1100Proper Aut
show all

MY1 Mechanically Jointed Rodless Cylinder

Create successful ePaper yourself

Delete template?

Save as template?