MY1 Mechanically Jointed Rodless Cylinder

Mechanically Jointed Rodless CylinderCam Follower Guide TypeSeries MY1C54Stroke Adjusting Unit SpecificationsBore size (mm)Unit symbolConfigurationShock absorber modelFine stroke adjustment range (mm)Stroke adjustment rangeJIS Symbol16 20A L A LShock Absorber SpecificationsModelMax. energy absorption (J)Stroke absorption (mm)Max. collision speed (mm/s)Max. operating frequency (cycle/min)Spring Extendedforce (N) RetractedOperating temperature range (°C)WithadjustingboltRB0806withadjustingboltHSpecificationsFluidActionOperating pressure rangeProof pressureAmbient and fluid temperatureCushionLubricationStroke length toleranceA25LFront/Side portBottom port16 20 25 32 40 50 63+1.81000 or less 01001 to 3000 +2.80M5 x 0.8ø40 to –5.6 0 to –6 0 to –11.5 0 to –12 0 to –16RB08062.96801.964.22WithadjustingboltHA32LAirDouble acting0.1 to 0.8 MPa1.2 MPa5 to 60°CAir cushionNon-lubeRc 1/8ø5 ø6Rc 1/4When exceeding the stroke fine adjustment range: Utilize a made-to-order specifications “-X416” and “-X417”.RB10075.97704.226.86RB0806withadjustingboltRB141219.6121500456.8615.98RB1007withadjustingbolt5 to 60Bore size (mm)Pipingport sizeWithadjustingboltRB201558.815258.3420.50RB1007withadjustingboltRB1412withadjustingboltRB272514725108.8320.01WithadjustingboltRB1412withadjustingboltHRB2015withadjustingboltAPiston Speed40Bore size (mm)Without stroke adjusting unitStrokeadjusting unitWithadjustingboltLRB1412withadjustingboltHA unitL unit and H unit+1.8+2.82700 or less 0 , 2701 to 5000 0RB2015withadjustingboltAWithadjustingbolt50LRB2015withadjustingboltø8HRB2725withadjustingboltRc 3/8ø10 ø11AWithadjustingbolt630 to –20 0 to –25LRB2015withadjustingbolt16 to 63100 to 1000 mm/s100 to 1000 mm/s100 to 1500 mm/s(1)(2)HRB2725withadjustingboltNote 1) Be aware that when the stroke adjusting range is increased bymanipulating the adjusting bolt, the air cushion capacity decreases.Also, when exceeding the air cushion stroke ranges on page 8-11-59., the piston speed should be 100 to 200 mm per second.Note 2) The piston speed is 100 to 1000 mm/s for centralized piping.Note 3) Use at a speed within the absorption capacity range. Refer to page8-11-59.MXMTSMYCYMGCXD--X20-DataSymbol-XB11-XC18-XC56-XC67-X168-X416-X417Made to Order Specifications(For details, refer to page 8-31-1.)SpecificationsLong strokeNPT finish piping portWith knock pin holeNBR rubber lining in dust seal bandHelical insert thread specificationsHolder mounting bracket ΙHolder mounting bracket ΙΙStandard StrokeBore size(mm)1620, 25, 32, 4050, 63Standard stroke (mm) ∗100, 200, 300, 400, 500, 600, 700800, 900, 1000, 1200, 1400, 16001800, 2000Maximum manufacturable stroke(mm)∗ Strokes are manufacturable in 1 mm increments, up to the maximum stroke. However, when exceeding a2000 mm stroke, specify “-XB11” at the end of the model number.300050008-11-57