Part 2: RECAP STANDARD MODULE - Smart Vend Corporation

More documents

Recommendations

Info

RECAP Software User's GuidePart 2: StandardPlanning theControl GroupParametersControl Groups contain settings for the various operating options of a controlunit. If you need to vary the operating parameters assigned to any one type ofcontrol unit (for instance, Towers), you must create more than one group forthat unit type.Planning the Control Group ParametersTo plan Control Groups, make copies of and fill out Tables B-6 throughB-9. The information you must provide in these tables is explained (inalphabetical order) throughout the remainder of this section. As you createeach Control Group, use Column 7 of Table B-1 to indicate which control unitsyou want associated with that group. Continue creating Control Groups until allof the control units listed in Table B-1 have a selected group. (Up to 99 ControlGroups can be created.)The following paragraphs provide a detailed explanation of each field in thecontrol group screens. The first line after the heading lists the equipmentassociated with each entry.Control Group DescriptionAllow $N BillAccumulator, CSC, Terminal, Tower-The descriptive name that identifiesthis control group-for instance, Swipe Unit Control contains the parametersrequired for Swipe Accumulator operations.CSC-Specifies the bill denominations (N represents 1,5, 10, or 20) a CardDispenser accepts for card purchases and RECHARGE (add value)operations. Acceptance criteria must be specified as follows:• ALWAYS-Accept this bill for card purchase and RECHARGE operations.• DISPENSE-Accept this bill for card purchase operations only .• RECHARGE- Accept this bill for RECHARGE operations only.• DISALLOW- Do not accept this bill.2-10 Planning the Standard Setup Parameters Planning the Control Group Parameters
Part 2: StandardRECAP Software User's GuideAuto DisableAuto Disable TimeAux Sense TypeCSC, Tower-Sets the anti-fraud, Auto Power Loss Disable feature, whichprevents fraudulent use of the unit, should it be stolen. You can set it toautomatically “lock up” after a pre-programmed period of time with nopower-thus preventing the thief from using the unit to add value to cards. Threesettings are available:• OFF- disables this security feature.• RECHARGE ONLY- prevents use of add value (RECHARGE)services. (the message CAN’T ADD VALUE appears in the DisplayWindow.)• COMPLETE DISABLE- Disables all user services (both dispensing andadd value).If either RECHARGE ONLY or COMPLETE DISABLE is selected, access toManagement Mode functions will also be prevented after a power loss. (Tounlock the unit, simply insert a Set Code Card that corresponds to the SiteCodes stored by the unit.)CSC, Tower-If you select either RECHARGE ONLY or COMPLETE DISABLE,you must decide how long you want the unit to wait before locking up after apower loss. Allowable settings are from one to 99 minutes. A setting ofapproximately 15 minutes helps to prevent lockups due to normal poweroutings (such as during thunder storms), yet provides a short enough timeinterval to make it unlikely that a vandal would re-supply power within that15-minute period.Terminal, Tower-Determines how the control unit detects auxiliary channelcopies (special copies, such as enlargements, for which an added fee ischarged). Foursettings are available:• NONE. Select this setting if your copier does not allow for use of auxiliarychannel pricing or if you choose not use this method of pricing. (To useauxiliary channel pricing, your copier must provide feedback that allows thecontrol unit to detect when a special copy is made. Refer to your copiermanual or contact your authorized copier technician to determine whetheryour copier has this ability.)• EARLY LEVEL MODE. Select this setting if the two auxiliary input lines fromthe copier are maintained at a constant voltage, or level (for example, 0 Volts),then changed to another constant level (e.g., 24 Volts) when a user selects aspecial function at the copier. (This “special function voltage” remainsconstant until the copier is returned to its normal copy setting.) When the unitdetects the special function voltage, it adjusts the cost per copy as requiredand prevents copier use if the card/cash value is less than the higher of thesetwo values:(1) the adjusted copy cost, or (2) the minimum cash/card value.• PULSE MODE. Select this setting if the two auxiliary input lines from thecopier transmit an electrical pulse each time a special copy is made.Planning the Control Group Parameters Planning the Standard Setup Parameters 2-11
Page 1 and 2: Part 2:RECAPSTANDARDMODULE
Page 3 and 4: TABLE OF CONTENTS1 What the Standar
Page 5 and 6: Part 2: StandardRECAP Software User
Page 15: Part 2: StandardRECAP Software User
Page 67 and 68:
Part 2: StandardRECAP Software User
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
INDEXAAccount Activity by Control U
Page 145:
PPlanning Control Groups . . . . .
show all

Part 2: RECAP STANDARD MODULE - Smart Vend Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?