Oakland Street Lighting Conversion Project - Navigator

More documents

Recommendations

Info

t. EMC Compliance. The driver and associated on-board circuitry shall meet theemission requirement for electronic noise of CISPR 15 - Class A emission limits inFCC Title 47, Sub Part B, Section 15.u. Noise Compliance. Class A sound rating per ANSI C63.4v. Rated useful lifetime of no less than 100,000 hours at ≤ 65ºC3. Luminaire Technical Parameters3.1 Electrical3.1.1 Operation from a 60 ±3 Hz AC line over a voltage ranging from 120 to 277 VAC.3.1.2 The standard operating voltages are 120 VAC and 240 VAC. The fluctuations of linevoltage should have no visible effect on the luminous output.3.1.3 The luminaires should function within an ambient operating temperature Range of -20°C to +40°C for 120 to 277 VAC.3.1.4 Surge Suppression. The luminaires on-board circuitry should include a surgeprotection device to withstand high repetition noise transients as a result of utility lineswitching, nearby lightning strikes, and other interference. For 120-277 VAC perIEEE/ANSI C62.41.-1991, 6kV/3kA Location Category B3 (120 Events).3.1.5 Conform to UL 1449, or UL 1283, depending on the components used in the design.3.1.6 Submit chip, diode, or package reliability test report for luminaire.3.1.7 RF Interference. Per the requirements set in Section 2.1.t.3.1.8 Frequency. Output operating frequency: ≥ 120 Hz (to avoid visible flicker) and inputoperating frequency of 60 Hz.3.1.9 LED Luminaires Efficacy and Efficiency. A minimum efficacy of 57 lumens per Wattlm/W) or better is desired. Allowing for thermal and optical losses, efficiency shouldbe determined on a delivered lumens per watt basis for comparison.3.2 Thermal Management3.2.1 Maximum junction temperature < 105 °C.3.2.2 The LED manufacturer’s maximum junction temperature for the expected life shouldnot be exceeded.3.3 Passive by design heat sink with no fans, pumps, or liquids.3.4 Physical and Mechanical Specifications3.4.1 Luminaire maximum weight: 46 pounds.3.4.2 The luminaire width maximum width: 17” wide.3.4.3 The housing should include a down opening door or doors for access to all internalcomponents. The housing should be a light or medium gray color with a flat or semiglosssheen and rust resistant paint that is corrosion resistant and tested to withstand aminimum 1,000 hours in salt and fog condition as defined in ASTM Standard B117.3.4.4 Long Life Zinc Nickel Plated Screws3.4.5 No polycarbonate parts unless it is UV stabilized (lens discoloration will beconsidered a failure under warranty).3.4.6 Each housing should be provided with a slip-fitter capable of mounting on aminimum 2.25 to 2.50-inch O.D. pipe tenon.3.4.6.1 The slip-fitter should be capable of being adjusted a minimum of ±5 degrees from theaxis of the tenon in a minimum of five steps (+5, +2.5, 0, -2.5, -5).3.4.6.2 The clamping brackets of the slip-fitter should not bottom out on the housing bosseswhen adjusted within the designed angular range.3.4.7 The luminaires should meet 3G Vibration Test per ANSI C136.31-2001 requirements.Page 9 of 24
3.4.8 Hinged access doors, capable of opening to 180 degrees are desired. The door shouldbe secured to the luminaires housing.3.4.9 Field wires connected to the luminaires shall terminate on a barrier type terminalblock secured to the housing. The terminal screws shall be captive and equipped withwire grips for conductors up to No. 6. Each terminal position shall be clearlyidentified.3.5 Housing Materials3.5.1 Die cast aluminum that is heavy duty and structurally rigid.3.5.2 Housing should be fabricated from materials that are designed to withstand a 1000-hour salt spray test as specified in ASTM Designation: B117.3.5.3 Each refractor or lens should be made from UV inhibited high-impact plastic such asacrylic or polycarbonate.3.5.4 Polymeric materials (if used) of enclosures containing either the power supply orelectronic components of the luminaires shall be made of UL94VO flame retardantmaterials. The lenses of the luminaires are excluded from this requirement.4.0 Other Requirements4.1 Fixture manufacture must have a minimum of 5000 units installed within the last year4.2 Photocell. Consultant shall install a new photocell with each new LED fixtureinstalled. The PC shall be an ordinary unit recommended by the vendor, not thedimming type PC.4.3 Fixture manufacture must provide test results from independent or National VoluntaryLaboratory Accreditation Program (NVLAP) certified laboratory.4.4 Application-Based Material Specifications. The Consultant shall provide anApplication-Based Material Specifications sheet, in Attachment L for each of theLuminaire proposed as part of the submittal for this RFP.4.5 Luminaires Photometric Evaluation. The Consultant shall provide the informationdata used for the Luminaires Photometric Evaluation as illustrated in Attachment M.The City will evaluate the data so provided by the Consultant for acceptability.4.6 Metal halide (MH) street lights. The Consultant shall provide the replacement of MHstreet lights like as if they are HPS street lights, and use the LED equivalents for HPSstreet lights for the replacement of MH street lights. The number of replacement ofMH street lights is expected to be small. The compensation would be equivalent tothat of the HPS. All MH street lights removed from the project will be disposed bythe Consultant.4.7 Low wattage street lights. The Consultant shall provide low wattage street lightswhich shall be the replacement of 50W HPS and 35W HPS. These units are located inpathways, tunnel, and in areas adjacent to real property or the right-of-way. A numberof the replacements would be by the LED equivalent of a 70W HPS. However, incases where this would lead to excessive brightness, the City will direct theConsultant to furnish one of the lower wattage LED equivalents. The number of unitsof low wattage street lights is expected to be small. The compensation would beequivalent to that of the 70W HPS.4.8 <strong>Oakland</strong> Standard Luminaires Matrix. The consultant shall provide luminairesequivalent to those listed below in the <strong>Oakland</strong> Standard Luminaires Matrix meetingthe Technical Specifications and subject to City approval. All the materials proposedshall be from a single manufacturer.Page 10 of 24
Page 1 and 2: City of OaklandDeanna Santana, City
Page 3 and 4: I. REQUEST FOR PROPOSALS SUMMARYPro
Page 5 and 6: 6. Capture of Savings. Document sav
Page 7 and 8: c. The PG&E Street Lights Data Base
Page 9: 1.11 IESNA LM-79-08 - IESNA Approve
Page 13 and 14: 2. There will be a monthly evaluati
Page 15 and 16: i. Project name and location.ii. Br
Page 17 and 18: a. Requirement - For this contract,
Page 19 and 20: workforce on Non-Construction Contr
Page 21 and 22: accordance with the Consultant Perf
Page 23 and 24: ecome the long term debt to be repa
Page 25 and 26: under the Public Records Act or Sun
Page 27 and 28: Print FormSCHEDULE EPROJECT CONSULT
Page 29 and 30: SCHEDULE OCONTRACTOR ACKNOWLEDGEMEN
Page 31 and 32: APPENDIX BCITY OF OAKLANDPUBLIC WOR
Page 33 and 34: APPENDIX Bset forth under the "Tota
Page 35 and 36: APPENDIX Bconstruction, the Enginee
Page 37 and 38: APPENDIX Bthe request is timely, fu
Page 39 and 40: APPENDIX Bused at the site of the e
Page 41 and 42: APPENDIX Bc. Direct equipment. The
Page 43 and 44: APPENDIX Bremove and dispose of the
Page 45 and 46: APPENDIX Bsafety, traffic, and prot
Page 47 and 48: APPENDIX BLiquidated damages shall
Page 49 and 50: APPENDIX Bprovided by the Resident
Page 51 and 52: APPENDIX Barea or shall be discharg
Page 53 and 54: APPENDIX BNothing specified herein
Page 55 and 56: APPENDIX BHazard Communication and
Page 57 and 58: APPENDIX BREPLACE SUBSECTION 7-11 W
Page 59 and 60: APPENDIX Bto subcontractors/ subcon
Page 61 and 62:
APPENDIX BPART 2 - CONSTRUCTION MAT
Page 63 and 64:
APPENDIX BOpen trench is performed
Page 65 and 66:
APPENDIX BThe conduit runs shall be
Page 67 and 68:
APPENDIX BADD NEW SUBSECTION 307-14
Page 69 and 70:
APPENDIX BATTACHMENTSNo. Attachment
Page 71 and 72:
APPENDIX BCONTR SUPPL Electrical Co
Page 73 and 74:
APPENDIX BAttachment No. 3MATERIAL
Page 75 and 76:
APPENDIX BAttachment 5As-Built Plan
Page 77 and 78:
APPENDIX BAttachment 8: LIMITED OPE
Page 79 and 80:
APPENDIX BContractor certifies that
Page 81 and 82:
APPENDIX Bf. Proof of InsuranceCont
Page 83 and 84:
APPENDIX BThe Contractor certifies
Page 85 and 86:
APPENDIX Bdeductible or self-insure
Page 87 and 88:
In the aggregate, progress payments
Page 89 and 90:
7. Ownership of ResultsAny interest
Page 91 and 92:
15. Indemnificationa. Notwithstandi
Page 93 and 94:
Disputed late payments are subject
Page 95 and 96:
iii.iv.Contractor shall immediately
Page 97 and 98:
origin, Acquired-Immune Deficiency
Page 99 and 100:
j. In the use of such recruitment,
Page 101 and 102:
deposited in the treasury or out of
Page 103 and 104:
(City of Oakland)Agency/DepartmentA
Page 105 and 106:
Department Head(Please Print Name o
Page 107:
EXHIBIT B - Billing Rates(insert bi
Page 127 and 128:
APPENDIX JAPPLICATION-BASED MATERIA
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
EPA: Maximum effective projected ar
Page 135 and 136:
CITY OF OAKLANDPROJECT DELIVERY DIV
Page 137:
Schedule L1All Questions rated at
show all

Oakland Street Lighting Conversion Project - Navigator

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?