RMP Underground Conduit System Installation Guide (Procedure 242)

More documents

Recommendations

Info

9.3 Customer Installs Pad Box – Single Phase Sectionalizing CabinetThe customer will install the pad box and conduits as shown in Figures 9.3.1 to 9.3.3.Note that the number of conduits may vary depending on the infrastructure design.Notes:For each conduit run:•One 45° elbow permanently attached•Elbow should terminate 6”-10” inside the pad box asshown.Equipment base leveled to 29" below final gradeEquipment base must be supported by compacted ¾ “ minusbackfillNot drawn to scaleLegendOpen ExcavationBackfillConduitPad BoxTop of Pad BoxProcedure6”-10”45° ElbowThe customer isresponsible to installthe bonding wire.Reference section 7.7.38”52”Figure 9.3.1 - Top View - Single Phase Sectionalizing Cabinet Pad BoxJ:\Publications\FPP\DIS\PRO\242-RMP Underground Conduit Systems.docx R6, 5/13/14This document is posted online at rockymountainpower.net, and at engineering’s intranet site for distribution procedures.Modification of this document must be authorized by PacifiCorp engineering publications, (503) 813-5293. 42
3” Final Grade6-10”3 – 6”45° ElbowProcedureFigure 9.3.2 - Side View - Single Phase Sectionalizing Cabinet Pad BoxThe pad box sits on properly compacted soil.Pad BoxThe conduitsenter under thepad box. Do notattempt to enterthe pad boxthrough the sideby making a holein the fiberglasspad box.45 ° ElbowFigure 9.3.3 - Conduit Placement - Single Phase Sectionalizing CabinetJ:\Publications\FPP\DIS\PRO\242-RMP Underground Conduit Systems.docx R6, 5/13/14This document is posted online at rockymountainpower.net, and at engineering’s intranet site for distribution procedures.Modification of this document must be authorized by PacifiCorp engineering publications, (503) 813-5293. 43
Page 3: ProcedureUnderground Conduit System
Page 7 and 8: Figure 6.5.2 - Joint Use Separation
Page 9 and 10: Underground Conduit Systemsfor Prim
Page 12 and 13: Any conduit system or any part of a
Page 14 and 15: ProcedureFiberglass conduit and swe
Page 16 and 17: 2.2.7 Conduit ProofingAll undergrou
Page 18 and 19: The following list of requirements
Page 20 and 21: ProcedureFigure 2.3.6.1 - Joint Use
Page 22: A padvault is a two-part concrete b
Page 25 and 26: 3.4 Secondary BoxesSecondary boxes,
Page 27 and 28: ProcedureFigure 4.2 - Clearances be
Page 29 and 30: Company is required to return to th
Page 31 and 32: 6 Installation Guidelines - Conduit
Page 33 and 34: 6.3 Installing Conduit through Pave
Page 35 and 36: 6.5 Joint Use SeparationFor joint u
Page 37 and 38: 6.6 Transition from Overhead to Und
Page 39 and 40: • Site accessibility. The site lo
Page 41 and 42: ProcedureFigure 7.6.1 - Barrier Pos
Page 43 and 44: 8 Three Phase Sectionalizing Cabine
Page 45 and 46: Notes:For each conduit run:•One 4
Page 47 and 48: Notes:For each conduit run:•Leave
Page 49: 9.2 Excavation - Single Phase Secti
Page 53: ProcedureFigure 10 - Single Phase T
Page 57 and 58: 10.4 Power Company Installs Pad Box
Page 59 and 60: 11.2 Excavation - Secondary BoxNote
Page 61 and 62: 12 Concrete Flat Pads - Customer Re
Page 63 and 64: 12.2 Excavation, Flat Pad - Three P
Page 65 and 66: ProcedureFigure 13.1 - Padvault13.2
Page 67 and 68: Pad vault must be set at proper ele
Page 69: UG CONDUIT SYSTEMS Rev. 6 May 2014E

RMP Underground Conduit System Installation Guide (Procedure 242)

Create successful ePaper yourself

Delete template?

Save as template?