IFC 110 F V2.0 IFC 110 F-EEx V2.0 - Krohne

More documents

Recommendations

Info

Sect. 3 Part A System installation and start-up3 Start-up• Before connecting to power, check that the instrument is correctly installed as described inSections 1 and 2.• The flowmeter, flow sensor and signal converter are delivered ready for operation. Alloperating data are set at the factory in accordance with your specifications.Please also refer to Section 2.7 ”Standard factory settings”.• Switch on the power supply. The flowmeter immediately begins to measure the flow.• When the power supply is switched on, the display successively shows START UP andREADY. Then the current flow rate and/or the current totalizer count are displayed. Displaysare either steady or cyclic depending on the setting described for Fct. 1.04.• 2 light-emitting diodes (LED) in the ”diagnostics” field on the front panel of the signalconverter indicate the status of measurement.LED displaysStatus of measurementGreen ”normal” LED Everything O.K.is flashingGreen ”normal” LED Momentary overload of outputs and/or A/D converter.and red ”error” LED Detailed error messages by setting Fct. 1.04 DISPLAY,are flashing alternately subfunction ”MESSAGES” to ”YES”, see Sections 4.4 and 5.5.Red ”error” LED is Fatal Error, see Sections 7.3 and 7.4flashingIMPORTANT!For EEx versions, also pay regard to all directions included in Sect. 6.1 and 13.Only the EEx flow sensor may be installed in the hazardous area. The EExcertified signal converter must be installed outside the hazardous area!26 IFC 110 F 05/2003
Part B IFC 110 F Signal converter Sect. 3Setting data: Here you can note down the settings of the signal converter !Fct. No. Function Settings1.01 Full-scale range1.02 Time constant1.03 Low-flow cut-off ON: OFF:1.04 Display FlowTotalizerMessagesTrend1.05 Current output I FunctionReverse rangeRange IError1.06 Pulse output P FunctionPulswidthPulse value1.07 Pulse output A1 orStatus output A1(for setting see below, Fct. 3.07,terminal A1)1.08 Status output A21.09 Status output A31.10 Status output A41.11 Control input C11.12 Control input C23.01 Language3.02 Flow sensor Meter sizeGK valueField frequencyPower frequencyFlow direction3.04 Entry code required ? no yes→ → → ↵ ↵ ↵ ↑ ↑ ↑3.05 User-defined unit3.06 Application Flow is steady pulsatingEmpty Pipe noDetection (EPD) yes3.07 Hardware-settings Terminal A1 is Pulse outputor Status output3.08 Measuring point3.09 Communication of HART or KROHNE RS 485Address:Baud rate:05/2003 IFC 110 F 27
Page 8 and 9: Sect. 1.3.1 Part A System installat
Page 16 and 17: Sect. 2.1 Part A System installatio
Page 28 and 29: Sect. 4.1 Part B IFC 110 F Signal c
Page 48 and 49: Sect. 5.11 Part B IFC 110 F Signal
Page 56 and 57: Sect. 6.1 Part C Special applicatio
Page 66 and 67: Sect. 6.10 Part C Special applicati
Page 76 and 77:
Sect. 7.6 Part C Special applicatio
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Sect. 10.1 Part D Technical Data, M
Page 90 and 91:
Page 92 and 93:
Sect. 11 Part D Technical Data, Mea
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Sect. 14 Part E Index14 IndexKeywor
Page 102 and 103:
Notice102 IFC 110 F 05/2003
Page 104:
AustraliaKROHNE Australia Pty Ltd.U
show all

IFC 110 F V2.0 IFC 110 F-EEx V2.0 - Krohne

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?