IFC 110 F V2.0 IFC 110 F-EEx V2.0 - Krohne

More documents

Recommendations

Info

Sect. 8.1 Part C Special applications, functional checks, service, and order numbers8 Service8.1 Replacing the power supply fuseSwitch off the power supply before opening the housing.1) Remove the cover from the terminal compartment (remove 2 screws).2) Unscrew the cap of the power supply fuse F.3) Replace fuse F5 or F6, type 5 x 20 G (Order No. see Sect. 9).F5: value for 100-230 V AC 0.8 A T, breaking capacity 1500 AF6: value for 24 V AC / DC 1.6 A T, breaking capacity 150 AF5/F6FPI/OPE/FEPSRSSSCS-EExWpower supply fuses, values are indicated aboveplug-in terminal for field current supply line, 4-pinplug-in terminal for outputs and inputs, 2x8-pinU-clamp terminal for connecting protective conductor PE or functional groundingconductor FEplug-in terminal for power supply line, 3-pinplug-in terminal for interface(s)U-clamp terminal for connecting the signal line shielding:signal line A: 2nd shield (7)signal line B: 3rd shield (11)plug-in terminal for electrode signal line, 5-pinSame as “S”, only available for hazardous duty versioninternal connection, may not be removed.I/ORS80 IFC 110 F 05/2003
Part C Special applications, functional checks, service, and order numbers Sect. 8.28.2 Retrofitting of magnetic sensors MP (optional)Switch off the power supply before opening the housing.1) Remove the cover from the terminal compartment (remove 2 screws).2) Pull all cables out of the plug-in terminals.3) Remove the glass cover from the control compartment (remove 4 screws).4) Remove 4 screws from the front panel F, take hold of the handle on the upper end of thefront panel and carefully pull the complete electronic unit out of the signal converter housing.5) Put down the electronic unit with the front panel F facing down (see illustration on the nextbut one page).6) Position the 2 mm (0.08”) thick insulating strip (Order No. 3 15940.01) loosely on top of theMP printed circuit board (PCB). The magnetic sensors and chip capacitor slip into the 4holes in the insulating strip. Slip the MP PCB and insulating strip from right to left betweenthe front panel and BDE PCB, taking care that the MP PCB and insulating strip are slippedthrough the three retaining clips H at the back of front panel F. Slip the socket connector ofthe MP PCB onto the (5-pin) plug connector PL MP .7) Fix the MP PCB with special steel tooth lock washer and nut S MP to establish contactbetween the back of the PCB and the back of the front panel. When correctly fitted, the MPPCB must be slightly bent between the final retaining clip H and the plug connector PL MP .8) Re-assemble in reverse order (items 4 to 1 above).9) Switch on the power supply. The ”magnet active” LED on the front panel is green.The function of the corresponding keys is tripped by touching the glass pane above the3 white fields ”→, ↵ and ↑” with the bar magnet. The LED lights up red, see Section 4.2,items and .05/2003 IFC 110 F 81
Page 8 and 9:
Sect. 1.3.1 Part A System installat
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Sect. 2.1 Part A System installatio
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Sect. 3 Part A System installation
Page 28 and 29:
Sect. 4.1 Part B IFC 110 F Signal c
Page 30 and 31: Sect. 4.3 Part B IFC 110 F Signal c
Page 48 and 49: Sect. 5.11 Part B IFC 110 F Signal
Page 56 and 57: Sect. 6.1 Part C Special applicatio
Page 66 and 67: Sect. 6.10 Part C Special applicati
Page 88 and 89: Sect. 10.1 Part D Technical Data, M
Page 92 and 93: Sect. 11 Part D Technical Data, Mea
Page 100 and 101: Sect. 14 Part E Index14 IndexKeywor
Page 102 and 103: Notice102 IFC 110 F 05/2003
Page 104: AustraliaKROHNE Australia Pty Ltd.U
show all

IFC 110 F V2.0 IFC 110 F-EEx V2.0 - Krohne

Create successful ePaper yourself

Delete template?

Save as template?