GENERAL CATALOG - K-Flex USA

More documents

Recommendations

Info

INSUL-SHEET ® /ROLL S2S DESIGNED FOR THE HVAC/R INDUSTRYINSUL-SHEET ®INSUL-SHEET ® flexible, fiber-free insulation preventscondensation, frost formation and heat/loss gain to createdurable, energy-efficient HVAC systems. Its closed cellstructure and tough skin inherently resists mold growthwithout the need for a jacket to provide these properties.Temperature Range: -297°F to 220°F (-182°C to 104°C) forpiping; -297°F to 200°F (-182°C to 93°C) for full adhesionDesigned for large surface areas (ducts, tanks and largediameter pipes). Reduced number of sections simplifiesinstallation, saving on time and labor costs.INSUL-SHEET ® WITH PSAINSUL-SHEET ® with PSA is flexible, fiber-free elastomericinsulation with a factory-applied pressure-sensitiveadhesive liner.Features of PSA: tear and moisture resistant easy releaseliner, reinforced scrim prevents stretching and improvespeel strength, reduced installation time and use ofcontact adhesives, and flexible and easy to install at lowtemperatures.Temperature range: -70°F to 200°F (-57°C to 93°C)R A N G ESHEETS36” X 48”PAGESTANDARD THICKNESSADHESIVE THICKNESS:1/8” to 2” 1/8” to 1-1/2”PAGE 38
Refer to K-Flex USA L.L.C.INSUL-SHEET ® /ROLL S2S TECHNICAL INFORMATIONUL 94(Recognition No. E300774)Made in USAContains a ProtectiveAntimicrobial AgentDESCRIPTIONINSUL-SHEET ® is an environmentallyfriendly, CFC-free, flexible elastomeric thermalinsulation. It is black in color and suppliedas flat sheets (36" x 48") in standardthicknesses of 1/8" thru 2". It is suppliedskin two sides in 1/4” and above. INSUL-SHEET ® is also available in rolls, with astandard roll width of 48". INSUL-SHEET ®key physical properties are approved throughsupervision by Factory Mutual ResearchCorporation.INSUL-SHEET ® is non-porous, fiber-freeand resists mold growth. An EPA-registeredantimicrobial agent is incorporated intothe product providing additional protectionagainst mold, fungal and bacterial growth.INSUL-SHEET ® is GREENGUARD ® certifiedas a low VOC material, meeting the requirementsof the “Children and Schools” and“Indoor Air Quality” classifications.APPLICATIONSINSUL-SHEET ® is used to retard heat gainand prevent condensation or frost formationon cold equipment, tanks, vessels,ducts, or large O.D. pipes. It also effectivelyretards heat loss when used on hot equipment,ducts, or large pipes. INSUL-SHEET ®is recommended for applications rangingfrom -297°F to 220°F (-182°C to 104°C)when used as pipe insulation where onlythe longitudinal seams and butt joints areglued. On full adhesion applications, theupper limit is 200°F (93°C).INSUL-SHEET ® has a tough skin that withstandstearing, rough handling, and severeenvironmental conditions, yet is flexible foreasy installation. INSUL-SHEET ® has superiorcold weather flexibility. INSUL-SHEET ®thickness has been calculated to controlcondensation on cold surfaces. Refer to thetable on the next page for specific recommendations.INSTALLATIONWhen INSUL-SHEET ® is applied to ductworkand equipment, use 100% coverage of anapproved contact adhesive. With a contactadhesive, both surfaces to be joined shouldbe coated and then joined after the adhesiveis dry to the touch. Compression jointswith adhesive applied should be used onall butt edges. INSUL-SHEET ® is also availablewith pre-applied pressure sensitiveadhesive (PSA) with an easy-to-use releaseliner. ASTM C1710, Installation Guide forFlexible Closed Cell Foams, should be usedas an installation guide.OUTDOOR APPLICATIONSFor optimum performance, outdoor applicationsrequire K-FLEX ® 374 Protective Coating,approved jacketing or K-FLEX ® Clad ALor WT. For more detailed information, referto the Application Guide.RESISTANCE TO MOISTUREVAPOR FLOWThe closed cell structure and uniqueformulation of INSUL-SHEET ® effectivelyretards the flow of moisture vapor, andis considered a low transmittance vaporretarder. For most applications, INSUL-SHEET ® needs no additional protection.Additional vapor barrier protection may benecessary for INSUL-SHEET ® when installedon low temperature surfaces that areexposed to continuous high humidity.FLAME AND SMOKE RATINGINSUL-SHEET ® in thicknesses of 2" (50mm) and below has a flame spread ratingof 25 or less and a smoke developmentrating of 50 or less as tested by ASTM E 84,“Surface Burning Characteristics of BuildingMaterials”.INSUL-SHEET ® is acceptable for use induct/plenum cover applications meetingthe requirements of NFPA 90A/B.Numerical flammability ratings alone may not definethe performance of products under actual fire conditions.They are provided only for use in the selection ofproducts to meet limits specified when compared to aknown standard.PAGE 39
Page 5: K-FLEX USA is a member of the IK In
Page 8 and 9: K-FLEX USA MARKETS INNOVATION IN IN
Page 10 and 11: DISTRIBUTION SHIPPING FROM YOUNGSVI
Page 12 and 13: K-FLEX IN THE WORLD DISTRIBUTION AN
Page 14 and 15: K-FLEX USA PACKAGINGINSUL-TUBE ® ,
Page 16 and 17: PHYSICAL PROPERTIES PERFORMANCE CHA
Page 18 and 19: PRODUCT CATEGORIESTUBES, SHEETS, RO
Page 20 and 21: PRODUCT RANGEPAGE 20
Page 22 and 23: INSUL-TUBE ® , INSUL-LOCK ® , INS
Page 24 and 25: Refer to K-Flex USA L.L.C.INSUL-TUB
Page 26: PIPE “R” VALUES PER SQUARE FOOT
Page 29 and 30: PIPE “R” VALUES PER SQUARE FOOT
Page 31 and 32: PYHSICAL PROPERTIES INSUL-LOCK ® T
Page 33 and 34: INSUL-LOCK ® WHITE TECHNICAL INFOR
Page 35 and 36: INSUL-LOCK ® WHITE “R” VALUESP
Page 37: PYHSICAL PROPERTIES INSUL-TUBE ® C
Page 41 and 42: THICKNESS RECOMMENDATIONS* - TO CON
Page 43 and 44: PYHSICAL PROPERTIES INSUL-SHEET ®
Page 45 and 46: K-FLEX ACCESSORIEScomplete range of
Page 47 and 48: K-FLEX ® ELASTOMERIC FOAM TAPE TEC
Page 49 and 50: K-FLEX ® 374 PROTECTIVE COATING TE
Page 51 and 52: PHYSICAL PROPERTIESColorBaseSolvent
Page 53 and 54: PHYSICAL PROPERTIESColor Amber (320
Page 55: PHYSICAL PROPERTIESColorSolventsVis
Page 58 and 59: K-FIT ® PREFABRICATED FITTINGSBENE
Page 60 and 61: K-FIT ® TECHNICAL INFORMATIONPHYSI
Page 62 and 63: PAGE 62
Page 64 and 65: K-FLEX CLAD ® AL 1-STEP APPLICATIO
Page 66 and 67: The all inclusive insulation system
Page 69 and 70: PHYSICAL PROPERTIES OF PVC/MYLAR ®
Page 71 and 72: K-FLEX CLAD ® WT NS TECHNICAL INFO
Page 73 and 74: K-FLEX CLAD ® IN PERFECT FOR LNG A
Page 75 and 76: PHYSICAL PROPERTIES OF K-FLEX CLAD
Page 77 and 78: K-FLEX CLAD ® TAPE WT TECHNICAL IN
Page 79 and 80: K-FLEX DUCT ® LINER GRAYdesigned f
Page 81 and 82: K-FLEX DUCT ® LINER GRAY TECHNICAL
Page 83 and 84: THICKNESS RECOMMENDATIONS* - TO CON
Page 85 and 86: K-FLEX ECO a halogen-free insulatio
Page 87 and 88: K-FLEX ECO TECHNICAL INFORMATIONUL
Page 89 and 90:
K-FLEX ® ELASTOMERIC FOAM TAPE - E
Page 91 and 92:
K-FONIKmaterials for noise reductio
Page 93 and 94:
K-FONIK APPLICATION GROUPSNOISE BAR
Page 95 and 96:
K-FONIK AB ACOUSTIC PERFORMANCENois
Page 97 and 98:
K-FONIK GK/GV ACOUSTIC PERFORMANCEG
Page 99 and 100:
SPECIFICATION BULLETINSTS1 Standard
show all

GENERAL CATALOG - K-Flex USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?