GENERAL CATALOG - K-Flex USA

More documents

Recommendations

Info

PYHSICAL PROPERTIES K-FLEX DUCT ® LINER GRAY TEST METHODSThermal Conductivity (K)75°F (24°C) Mean Temp 0.25 (0.036) ASTM C 177BTU - in/hr - Ft 2 - °F (W/mK)Density 3-6 PCF ASTM D 1622/ ASTM D 3575Operating Temperature RangeUpperLower200°F (93°C)-40°F (-40°C)Water Vapor Permeability Dry Cup. Perm-In
THICKNESS RECOMMENDATIONS* - TO CONTROL CONDENSATIONOUTSIDE TEMPERATURESURFACE TEMPERATURE50°F 10°C 35°F 2°C 0°F -18°C -20°F -29°CMild Conditions (Max 80°F, 26°C - 50% R.H.) 1/8” 3 mm 1/4” 6 mm 1/2” 13 mm 3/4” 19 mmNormal Conditions (Max 85°F, 29°C - 70% R.H.) 1/2” 13 mm 3/4” 19 mm 1” 25 mm 1-1/4” 32 mmSevere Conditions (Max 90°F, 32°C - 80% R.H.) 3/4” 19 mm 1” 25 mm 1-3/4” 44 mm 2” 51 mm*K-FLEX Duct ® Liner Gray in thickness noted within the specified temperature ranges will prevent condensation under design conditions defined below.K-FLEX Duct ® Liner Gray is not available in all thicknesses listed.Mild: Typical conditions are most air-conditioned spaces and arid climates.Normal: Maximum severity of indoor conditions rarely exceed 85°F (29°C) and 70% R.H. in United States.Severe: Generally found in areas where excessive moisture is introduced or in poorly ventilated areas where the temperature may be depressed below theambient. Under conditions of high humidity, additional thickness of insulation may be required.NOTE: Thickness recommendations calculated using 0.2575 K-factor (0.25 plus 3% test error allowance)SHEET “R” VALUESR Value 1/2” R Value 3/4” R Value 1” R Value 1-1/2” R Value 2”2.0 3.0 4.2 6.0 8.0All sizes are nominal.Note:“R” values were calculated using a K factor of 0.2575 (0.25 plus 3% test error allowance at 75°F, 24°C mean temp.) and nominal thickness ineach case. Lower operating temperatures will result in improved R values. Contact Technical Services for specific recommendations.SPECIFICATION COMPLIANCE• ASTM C534 Type 2 (Sheet), Grade 1• ASTM C1534• ASTM D1056-00-2B1• ASTM C423/E795 NRC=0.50 at 1” thickness• New York City MEA 186-86-M Vol. V• USDA Compliant• RoHS Compliant• UL 94-5V Flammability Classification (RecognitionNo. E300774)• ASTM E84: 25/50 at 2” and below• Meets requirements of NFPA 90A Sect. 2.3.3for Supplementary Materials for Air DistributionSystems up to 2” thickness• Meets requirements of UL 181 Sections 11.0and 16.0 (Mold Growth/Air Erosion)• Meets requirements of ASTM C411 (Test Methodfor Hot Surface Performance of High TemperatureThermal Insulation)• GREENGUARD certified under the “Children &Schools” and “Indoor Air Quality” classifications• Meets energy code requirements for ASHRAE 90.1and 189.1PAGE 83
Page 5:
K-FLEX USA is a member of the IK In
Page 8 and 9:
K-FLEX USA MARKETS INNOVATION IN IN
Page 10 and 11:
DISTRIBUTION SHIPPING FROM YOUNGSVI
Page 12 and 13:
K-FLEX IN THE WORLD DISTRIBUTION AN
Page 14 and 15:
K-FLEX USA PACKAGINGINSUL-TUBE ® ,
Page 16 and 17:
PHYSICAL PROPERTIES PERFORMANCE CHA
Page 18 and 19:
PRODUCT CATEGORIESTUBES, SHEETS, RO
Page 20 and 21:
PRODUCT RANGEPAGE 20
Page 22 and 23:
INSUL-TUBE ® , INSUL-LOCK ® , INS
Page 24 and 25:
Refer to K-Flex USA L.L.C.INSUL-TUB
Page 26:
PIPE “R” VALUES PER SQUARE FOOT
Page 29 and 30:
PIPE “R” VALUES PER SQUARE FOOT
Page 31 and 32: PYHSICAL PROPERTIES INSUL-LOCK ® T
Page 33 and 34: INSUL-LOCK ® WHITE TECHNICAL INFOR
Page 35 and 36: INSUL-LOCK ® WHITE “R” VALUESP
Page 37 and 38: PYHSICAL PROPERTIES INSUL-TUBE ® C
Page 39 and 40: Refer to K-Flex USA L.L.C.INSUL-SHE
Page 41 and 42: THICKNESS RECOMMENDATIONS* - TO CON
Page 43 and 44: PYHSICAL PROPERTIES INSUL-SHEET ®
Page 45 and 46: K-FLEX ACCESSORIEScomplete range of
Page 47 and 48: K-FLEX ® ELASTOMERIC FOAM TAPE TEC
Page 49 and 50: K-FLEX ® 374 PROTECTIVE COATING TE
Page 51 and 52: PHYSICAL PROPERTIESColorBaseSolvent
Page 53 and 54: PHYSICAL PROPERTIESColor Amber (320
Page 55: PHYSICAL PROPERTIESColorSolventsVis
Page 58 and 59: K-FIT ® PREFABRICATED FITTINGSBENE
Page 60 and 61: K-FIT ® TECHNICAL INFORMATIONPHYSI
Page 62 and 63: PAGE 62
Page 64 and 65: K-FLEX CLAD ® AL 1-STEP APPLICATIO
Page 66 and 67: The all inclusive insulation system
Page 69 and 70: PHYSICAL PROPERTIES OF PVC/MYLAR ®
Page 71 and 72: K-FLEX CLAD ® WT NS TECHNICAL INFO
Page 73 and 74: K-FLEX CLAD ® IN PERFECT FOR LNG A
Page 75 and 76: PHYSICAL PROPERTIES OF K-FLEX CLAD
Page 77 and 78: K-FLEX CLAD ® TAPE WT TECHNICAL IN
Page 79 and 80: K-FLEX DUCT ® LINER GRAYdesigned f
Page 81: K-FLEX DUCT ® LINER GRAY TECHNICAL
Page 85 and 86: K-FLEX ECO a halogen-free insulatio
Page 87 and 88: K-FLEX ECO TECHNICAL INFORMATIONUL
Page 89 and 90: K-FLEX ® ELASTOMERIC FOAM TAPE - E
Page 91 and 92: K-FONIKmaterials for noise reductio
Page 93 and 94: K-FONIK APPLICATION GROUPSNOISE BAR
Page 95 and 96: K-FONIK AB ACOUSTIC PERFORMANCENois
Page 97 and 98: K-FONIK GK/GV ACOUSTIC PERFORMANCEG
Page 99 and 100: SPECIFICATION BULLETINSTS1 Standard
show all

GENERAL CATALOG - K-Flex USA

Create successful ePaper yourself

Delete template?

Save as template?