GENERAL CATALOG - K-Flex USA

More documents

Recommendations

Info

K-FLEX ® 320/620 CONTACT ADHESIVE TECHNICAL INFORMATIONMade in <strong>USA</strong>DESCRIPTIONK-FLEX ® 320 & 620 Contact Adhesives areair-drying solvent-based neoprene contactadhesives that are excellent for joiningseams and butt joints of elastomeric& polyolefin pipe and sheet Insulation.K-FLEX ® 320 & 620 Contact Adhesivesmake resilient moisture- and heat-resistantbonds when used with elastomericand polyolefin products. K-FLEX ® 320 &620 Contact Adhesives’ higher solids contentallows them to be brushed or rollerapplied easily without running. They areideal for bonding porous and non-porousmaterials, as they will not be absorbedeasily.Caution: Adhesive contains notable solventsand container not in use shouldbe kept closed. Keep adhesive awayfrom sparks and open flames. Use withadequate ventilation and avoid excessivecontact with the skin.USESK-FLEX ® 320 & 620 Contact Adhesivesmay be used for bonding elastomeric andpolyolefin products to a variety of materials(i.e., other elastomers, metal, wood,leather, felt, concrete, etc.). The adhesiveswill make resilient and heat-resistantbonds. They are suitable for line temperaturesup to 220˚F (104˚C) on applicationsrequiring bonded seams and joints. Whenthe adhesives are applied to large flat orcurve surfaces, they are suitable for temperaturesup to 200˚F (93˚C). The productsare supplied in a variety of sizes rangingfrom pint brush top containers to galloncontainers. Larger containers are availableupon request.APPLICATION INSTRUCTIONSFor proper adhesion, the surfaces towhich the insulation is to be appliedmust be thoroughly cleaned, dry andunheated. Primed and painted surfacesshould be adhesive tested to be sure theinsulation will not lift off after application.The adhesive should be thoroughlymixed. Brush or roll a thin even coat ofadhesive on both surfaces to be joined.Allow the adhesive films to become dryto the touch, but tacky, before joining thesurfaces. Press the two surfaces together.Be sure the insulation is in the desiredposition before the adhesive surfacesmake initial contact, since the adhesiveforms an instant bond, and repositioningafter contact is difficult. Moderatepressure should then be applied to theentire bonding area to ensure completecontact. Avoid heat, sparks, and openflames, and use only proper ventilation.Close container after use. K-FLEX ® 320 &620 Contact Adhesives should be appliedat above 40˚F (4˚C) temperatures, andallowed to dry for 24 hours before equipmentoperation. Protective coatings can beapplied to applications with bonded jointsand seams, after allowing 24 hours drytime. Applications such as large tanks, orvessels where full adhesive coverage isrequired, must be allowed to dry 7 daysprior to applying a protective coating.The surface may be allowed to dry andcan be solvent reactivated by wiping witha toluene dampened cloth.Thinning the adhesive is not recommended.Common lacquer thinners can be usedfor clean up.PAGE 52
PHYSICAL PROPERTIESColor Amber (320), Black (620)BaseSolventsViscosityNeopreneToluene, Hexane, AcetoneMedium SyrupSolid Content 25% ± 2%Weight per gallonCoverage6.98± .2 lbs.200 sq. ft. per gallon (one surface)Shelf Life One year in original sealed container. Storage temperature 60°FMinimum Dry TimeOpen Time2-4 minutes under normal conditionsNot to exceed 10 minutesTemperature Limits220°F (104°C) for pipe insulation seams and joints200°F (93°C) for full bonding sheetsFlammabilityASTM E84 10/0 Flamespread/Smoke DevelopedFlash PointLess than -4°FFreight Classifications • Adhesives NOS. Flammable Liquid 4620 Sub 5, class 60, Un 1133, IMDG class 3.1• PG:11 (packaging group II)PAGE 53
Page 5: K-FLEX USA is a member of the IK In
Page 8 and 9: K-FLEX USA MARKETS INNOVATION IN IN
Page 10 and 11: DISTRIBUTION SHIPPING FROM YOUNGSVI
Page 12 and 13: K-FLEX IN THE WORLD DISTRIBUTION AN
Page 14 and 15: K-FLEX USA PACKAGINGINSUL-TUBE ® ,
Page 16 and 17: PHYSICAL PROPERTIES PERFORMANCE CHA
Page 18 and 19: PRODUCT CATEGORIESTUBES, SHEETS, RO
Page 20 and 21: PRODUCT RANGEPAGE 20
Page 22 and 23: INSUL-TUBE ® , INSUL-LOCK ® , INS
Page 24 and 25: Refer to K-Flex USA L.L.C.INSUL-TUB
Page 26: PIPE “R” VALUES PER SQUARE FOOT
Page 29 and 30: PIPE “R” VALUES PER SQUARE FOOT
Page 31 and 32: PYHSICAL PROPERTIES INSUL-LOCK ® T
Page 33 and 34: INSUL-LOCK ® WHITE TECHNICAL INFOR
Page 35 and 36: INSUL-LOCK ® WHITE “R” VALUESP
Page 37 and 38: PYHSICAL PROPERTIES INSUL-TUBE ® C
Page 39 and 40: Refer to K-Flex USA L.L.C.INSUL-SHE
Page 41 and 42: THICKNESS RECOMMENDATIONS* - TO CON
Page 43 and 44: PYHSICAL PROPERTIES INSUL-SHEET ®
Page 45 and 46: K-FLEX ACCESSORIEScomplete range of
Page 47 and 48: K-FLEX ® ELASTOMERIC FOAM TAPE TEC
Page 49 and 50: K-FLEX ® 374 PROTECTIVE COATING TE
Page 51: PHYSICAL PROPERTIESColorBaseSolvent
Page 55: PHYSICAL PROPERTIESColorSolventsVis
Page 58 and 59: K-FIT ® PREFABRICATED FITTINGSBENE
Page 60 and 61: K-FIT ® TECHNICAL INFORMATIONPHYSI
Page 62 and 63: PAGE 62
Page 64 and 65: K-FLEX CLAD ® AL 1-STEP APPLICATIO
Page 66 and 67: The all inclusive insulation system
Page 69 and 70: PHYSICAL PROPERTIES OF PVC/MYLAR ®
Page 71 and 72: K-FLEX CLAD ® WT NS TECHNICAL INFO
Page 73 and 74: K-FLEX CLAD ® IN PERFECT FOR LNG A
Page 75 and 76: PHYSICAL PROPERTIES OF K-FLEX CLAD
Page 77 and 78: K-FLEX CLAD ® TAPE WT TECHNICAL IN
Page 79 and 80: K-FLEX DUCT ® LINER GRAYdesigned f
Page 81 and 82: K-FLEX DUCT ® LINER GRAY TECHNICAL
Page 83 and 84: THICKNESS RECOMMENDATIONS* - TO CON
Page 85 and 86: K-FLEX ECO a halogen-free insulatio
Page 87 and 88: K-FLEX ECO TECHNICAL INFORMATIONUL
Page 89 and 90: K-FLEX ® ELASTOMERIC FOAM TAPE - E
Page 91 and 92: K-FONIKmaterials for noise reductio
Page 93 and 94: K-FONIK APPLICATION GROUPSNOISE BAR
Page 95 and 96: K-FONIK AB ACOUSTIC PERFORMANCENois
Page 97 and 98: K-FONIK GK/GV ACOUSTIC PERFORMANCEG
Page 99 and 100: SPECIFICATION BULLETINSTS1 Standard

GENERAL CATALOG - K-Flex USA

Create successful ePaper yourself

Delete template?

Save as template?