GENERAL CATALOG - K-Flex USA

More documents

Recommendations

Info

K-FLEX CLAD ® IN TECHNICAL INFORMATIONMade in <strong>USA</strong>Contains a ProtectiveAntimicrobial AgentDESCRIPTIONK-FLEX Clad ® IN, available in both tubularand sheet form, is a composite product ofclosed cell elastomeric insulation adheredto a gray polymeric sheet.K-FLEX Clad ® IN is fiber-free, non-porousCFC- and HCFC-free. These characteristicsallow it to comply with Health, Safety andEnvironmental requirements. It providessalt water and impact resistance, as wellas UV protection, making it an excellentchoice for severe outdoor conditions.K-FLEX Clad ® IN is available in 3-footlength tubes up to 1-1/2” wall thickness.Sheet product is available in 36” x 48”sheets or 36” wide rolls up to 2” thickness.K-FLEX Clad ® IN is available with K-FLEX ®LS or with K-FLEX ECO insulation. (Seeseparate data sheet for K-FLEX ECOphysical properties.) Full line of accessoryproducts (tape and adhesives) areavailable.The polymeric sheet cladding provides asecondary moisture vapor barrier to theinherently moisture resistant closed cellfoam core.APPLICATIONSK-FLEX Clad ® IN is an ideal choice for industrialplants, offshore platforms, FPSO’s,LNG Terminals and for the shipbuildingindustry. It is well-suited for extreme temperatureapplications due to the ability ofthe outer polymeric covering to expand andcontract with rapid temperature cycles.K-FLEX Clad ® IN - ECO meets IMO requirementsfor shipbuilding and off-shoreplatforms.K-FLEX Clad ® IN has a low thermal conductivity,a high water vapor diffusion resistancefactor, and practically eliminates theproblem of under insulation corrosion. It iseasy to install and combines excellent performancewith low maintenance requirements.The cladding is flexible enough toprotect against damage from traffic (doesnot dent like traditional metal jackets) andallows for easy maintenance.K-FLEX Clad ® IN with elastomeric insulationcore can be used over a wide rangeof temperatures from -297°F to +220°F(-182°C to +104°C). K-FLEX Clad ® IN -ECO (halogen-free) should be used as thecore insulation on stainless steel applicationsabove 100°F. The temperature rangefor K-FLEX Clad ® IN - ECO is -297°F to+300°F (-182°C to +150°C).INSTALLATIONA unique overlap closure system, whicheliminates through seams on longitudinalseams, ensures against moisture penetration.No special tools and fewer materialsare necessary at the job site, allowing forquick installation.K-FLEX ® 320 Contact Adhesive is an aggressiveadhesive specially formulated forthe clad jacket and insulation core systemand is recommended for longitudinal, buttand overlap seams.PAGE 74
PHYSICAL PROPERTIES OF K-FLEX CLAD ® IN POLYMERIC SHEETATTRIBUTES K-FLEX CLAD ® IN TEST METHODSMaterial TypeChlorosulfonated PolyethyleneThickness 0.30”Reaction to Fire 25/350 ASTM E 84Water Vapor Diffusion 0.001 ASTM E 96Weather, UV Resistance Excellent ASTM G 53Corrosion RiskThe system provides protection for corrosion under insulationSalt Spray Resistance Excellent BS 903 F12Wear Resistance Excellent BS 903 A2Ozone Resistance Excellent BS 903 A43, ASTM D1171Chemical Resistance Excellent Acids, Alcohols, Alkalies, OilsTensile Elongation >100% BS 903 A2ColorGrayPHYSICAL PROPERTIES OF ELASTOMERIC CORE MATERIAL (STANDARD)Temperature Range/Sheet -297°F to +220°F (-182°C to + 104°C) ASTM C 411ColorBlackThermal Conductivity (75°F Mean temp) 0.245 BTU-in/hr-ft 2 -°F ASTM C 177, ASTM C 518Water vapor permeability 0.03 perm-in ASTM E 96Water absorption % 90Dimensional Stability
Page 5:
K-FLEX USA is a member of the IK In
Page 8 and 9:
K-FLEX USA MARKETS INNOVATION IN IN
Page 10 and 11:
DISTRIBUTION SHIPPING FROM YOUNGSVI
Page 12 and 13:
K-FLEX IN THE WORLD DISTRIBUTION AN
Page 14 and 15:
K-FLEX USA PACKAGINGINSUL-TUBE ® ,
Page 16 and 17:
PHYSICAL PROPERTIES PERFORMANCE CHA
Page 18 and 19:
PRODUCT CATEGORIESTUBES, SHEETS, RO
Page 20 and 21:
PRODUCT RANGEPAGE 20
Page 22 and 23:
INSUL-TUBE ® , INSUL-LOCK ® , INS
Page 24 and 25: Refer to K-Flex USA L.L.C.INSUL-TUB
Page 26: PIPE “R” VALUES PER SQUARE FOOT
Page 29 and 30: PIPE “R” VALUES PER SQUARE FOOT
Page 31 and 32: PYHSICAL PROPERTIES INSUL-LOCK ® T
Page 33 and 34: INSUL-LOCK ® WHITE TECHNICAL INFOR
Page 35 and 36: INSUL-LOCK ® WHITE “R” VALUESP
Page 37 and 38: PYHSICAL PROPERTIES INSUL-TUBE ® C
Page 39 and 40: Refer to K-Flex USA L.L.C.INSUL-SHE
Page 41 and 42: THICKNESS RECOMMENDATIONS* - TO CON
Page 43 and 44: PYHSICAL PROPERTIES INSUL-SHEET ®
Page 45 and 46: K-FLEX ACCESSORIEScomplete range of
Page 47 and 48: K-FLEX ® ELASTOMERIC FOAM TAPE TEC
Page 49 and 50: K-FLEX ® 374 PROTECTIVE COATING TE
Page 51 and 52: PHYSICAL PROPERTIESColorBaseSolvent
Page 53 and 54: PHYSICAL PROPERTIESColor Amber (320
Page 55: PHYSICAL PROPERTIESColorSolventsVis
Page 58 and 59: K-FIT ® PREFABRICATED FITTINGSBENE
Page 60 and 61: K-FIT ® TECHNICAL INFORMATIONPHYSI
Page 62 and 63: PAGE 62
Page 64 and 65: K-FLEX CLAD ® AL 1-STEP APPLICATIO
Page 66 and 67: The all inclusive insulation system
Page 69 and 70: PHYSICAL PROPERTIES OF PVC/MYLAR ®
Page 71 and 72: K-FLEX CLAD ® WT NS TECHNICAL INFO
Page 73: K-FLEX CLAD ® IN PERFECT FOR LNG A
Page 77 and 78: K-FLEX CLAD ® TAPE WT TECHNICAL IN
Page 79 and 80: K-FLEX DUCT ® LINER GRAYdesigned f
Page 81 and 82: K-FLEX DUCT ® LINER GRAY TECHNICAL
Page 83 and 84: THICKNESS RECOMMENDATIONS* - TO CON
Page 85 and 86: K-FLEX ECO a halogen-free insulatio
Page 87 and 88: K-FLEX ECO TECHNICAL INFORMATIONUL
Page 89 and 90: K-FLEX ® ELASTOMERIC FOAM TAPE - E
Page 91 and 92: K-FONIKmaterials for noise reductio
Page 93 and 94: K-FONIK APPLICATION GROUPSNOISE BAR
Page 95 and 96: K-FONIK AB ACOUSTIC PERFORMANCENois
Page 97 and 98: K-FONIK GK/GV ACOUSTIC PERFORMANCEG
Page 99 and 100: SPECIFICATION BULLETINSTS1 Standard
show all

GENERAL CATALOG - K-Flex USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?