27.12.2012 Views

Bureau of Land Management's Decision Record and Environmental

Bureau of Land Management's Decision Record and Environmental

Bureau of Land Management's Decision Record and Environmental

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

Jersey Valley Geothermal Development Project<br />

<strong>Environmental</strong> Assessment: NV063 -EAO8-09 1<br />

2.1.4 Rights-<strong>of</strong>-Way for the Power Line <strong>and</strong> Access Road<br />

The Proposed Action also includes the construction <strong>and</strong> operation <strong>of</strong> an approximately<br />

27.59-mile overhead electrical transmission line (NVN-87409) originating at the proposed Jersey<br />

Valley power plant <strong>and</strong> terminating at the proposed SPPCo. Bannock substation (see Figure 3).<br />

An additional ROW is requested from <strong>L<strong>and</strong></strong>er County’s Buffalo Valley Road to the proposed<br />

SPPCo. Bannock substation <strong>and</strong>/or switching station. The proposed road is located seven (7)<br />

miles west <strong>of</strong> the junction <strong>of</strong> Highway 305 <strong>and</strong> the Buffalo Valley junction, <strong>and</strong> extends south<br />

approximately 0.50 miles to the substation <strong>and</strong>/or switching station (see Figure 11).<br />

2.1.5 Transmission Line Corridor<br />

Ormat is also proposing to construct, operate <strong>and</strong> maintain an approximately 27.59 mile<br />

overhead 120 kV transmission line, originating at the proposed Jersey Valley power plant site<br />

<strong>and</strong> terminating at a proposed SPPCo. Bannock substation in the NE1/4, SE1/4 Section 28,<br />

T3ON, R43E; which is located on private l<strong>and</strong>s (see Figure 3). The proposed transmission line<br />

would require a 200-foot wide ROW (90-foot permanent width <strong>and</strong> an additional 110-foot<br />

temporary width required for construction).<br />

Design characteristics can be found in Table 3.<br />

Table 3: Transmission Line Typical Design Characteristics<br />

Line length Approximately 27.59 miles<br />

Type <strong>of</strong> structure Single pole<br />

Structure height Single pole: 55 to 70 feet<br />

Span length Single pole: Approximately 300 to 400 feet<br />

Number <strong>of</strong> structures/mile Single pole: Approximately 14 to 18 per mile<br />

Voltage 120,000<br />

2.1.5.1 Facility Design Factors <strong>and</strong> Additional Components<br />

The transmission line would be designed to meet all temperature, wind, voltage, span <strong>and</strong><br />

structure height clearance requirements. The proposed transmission line would also provide<br />

raptor protection in compliance with the st<strong>and</strong>ards described in the “Suggested Practices for<br />

Raptor Protection on Power Lines, The State <strong>of</strong> the Art in 2006” (APLIC 2006). To prevent<br />

perching, a cone (Kaddas Enterprises type KE1058 or equal) would be installed on the top <strong>of</strong><br />

each transmission line pole along the entirety <strong>of</strong> the transmission line (see Figure 12 <strong>and</strong> Figure<br />

13).<br />

Staging areas would be located on public l<strong>and</strong> <strong>and</strong> would be used to temporarily store materials<br />

required for construction (see Table 4 <strong>and</strong> Figure 5).<br />

- 15-

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!