CANopen Basics Instruction Manual pdf - Kuhnke

More documents

Recommendations

Info

Project Setup The current display is: � Station 2 is being monitored (see circle) � None of the other stations is being monitored 60 E 615 GB 06.02.2008
Project Setup 5.1.11.1.2 CANopen Kernel Status of the CANopen Manager Operands CSO08.00 to CSO08.07 indicate the status of the CANopen kernel. Their output stands for the following: Operand Bit Value Explanation CSO08.00 Kernel status code: 0 0 Channel 1 online 1 1 Channel 1 bus off 0 Channel 1 error active E 615 GB 61 06.02.2008 1 Channel 1 error passive (error frames encountered) 2 0 Channel 1 no overrun 1 Channel 1 overrun 3 Not used 4 Not used 5 Not used 6 0 Channel 1 operational 1 Channel 1 not operational 7 Not used CSO08.01 Own node ID CSO08.02 Number of emergency frames CSO08.03 Number of kernel errors CSO08.04 Baud rate (LB) [kbit/s] CSO08.05 Baud rate (HB) [kbit/s] CSO08.06 Config counter (LB) CSO08.07 Config counter (HB)
Page 1 and 2:
Kuhnke Electronics Instruction Manu
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 6.1.3 PDO Manager
Page 7 and 8:
1 Introduction Introduction Next to
Page 9 and 10: 1.2 Bus Location Introduction The s
Page 11 and 12: 2 Reliability, Safety 2.1 Target Gr
Page 13 and 14: 2.3.5 Instruction Reliability, Safe
Page 15 and 16: 2.4.1 Project Planning and Installa
Page 17 and 18: 2.5 Electromagnetic Compatibility 2
Page 19 and 20: Reliability, Safety 2.5.5 Protectio
Page 21 and 22: Network Configuration (Hardware) 3
Page 23 and 24: 3.3 Bus Cable 3.3.1 Material Networ
Page 25 and 26: 3.4 Line Interfacing 3.4.1 D-Sub So
Page 27 and 28: Network Configuration (Hardware) Th
Page 29 and 30: Network Configuration (Software) 4
Page 31 and 32: 4.2.2 Using COBES Network Configura
Page 33 and 34: • OK • Go to section 4.2.2.2 4.
Page 35 and 36: 4.2.2.4 Further Functions Network C
Page 37 and 38: 5 Setting up Projects Project Setup
Page 39 and 40: 5.1.2 Start ProCANopen Project Setu
Page 41 and 42: Project Setup • Specify a name an
Page 43 and 44: Project Setup This will close the "
Page 45 and 46: 5.1.6 Define the Communication Path
Page 47 and 48: Project Setup Two double arrows in
Page 49 and 50: Project Setup Network Name and Info
Page 51 and 52: The information in the window will
Page 53 and 54: 5.1.8 Transfer the Data to the PLC
Page 55 and 56: Write a Test Program for the PLC ;
Page 57 and 58: 5.1.10 Test the Communication Proje
Page 59: 5.1.11.1 Analyse Messages Project S
Page 63: Project Setup � CSO08.06 = Config
Page 66 and 67: Project Setup 5.2.2 Configuration S
Page 68 and 69: Project Setup For notes on which fo
Page 70 and 71: Project Setup 5.2.6 Applicable Vari
Page 72 and 73: Kuhnke Control Units 6.1.2 NMT Mast
Page 74 and 75: Kuhnke Control Units 6.2 KUBES Modu
Page 76 and 77: Kuhnke Control Units 6.2.3 Read Ker
Page 78 and 79: Kuhnke Control Units Parameters: In
Page 80 and 81: Kuhnke Control Units Output Functio
Page 82 and 83: Kuhnke Control Units Output Functio
Page 84 and 85: Kuhnke Control Units C/D SO10.08 Da
Page 86 and 87: Kuhnke Control Units 86 E 615 GB 06
Page 88 and 89: CANopen Basics 7.2.1 Bus Allocation
Page 90 and 91: CANopen Basics 7.4 Mechanisms of Co
Page 92 and 93: CANopen Basics 7.4.4 Emergency Mess
Page 94 and 95: CANopen Basics 7.4.5.2 Heartbeat Me
Page 96 and 97: CANopen Basics 7.5.1 PDO Mapping Th
Page 98 and 99: CANopen Basics 98 E 615 GB 06.02.20
Page 100 and 101: Appendix 8.2 Abbreviations CAN Cont
Page 102 and 103: Appendix 8.4 Index address ........
show all

CANopen Basics Instruction Manual pdf - Kuhnke

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?