CV7300 Instruction Manual - TECO-Westinghouse Motor Company

More documents

Recommendations

Info

– Frequency Command by 1-06 4-2 Chapter 4 Software Index To Change the Remote/Local mode, you must push FWD/REV and《/RESET key at the same time. The Remote /Local mode of change can used in STOP mode, it can’t used in Run mode.
Page 2:
Quick Start Guide This guide is to
Page 6:
Table of Content Quick Start Guide
Page 10:
Chapter 0 Preface Chapter 0 Preface
Page 14: 1.1.2 During Power ON Danger Chapte
Page 18: Chapter 2 Definition of model Inver
Page 22: 3.2 Environmental precautions Do no
Page 26: 3-4 Chapter 3 Ambient Environment a
Page 30: ※Notice 3-6 Chapter 3 Ambient Env
Page 34: Chapter 3 Ambient Environment and I
Page 38: Chapter 3 Ambient Environment and I
Page 42: 3.4.2 General Specifications Freque
Page 46: ※Note 2:-10 ~ 50℃ in distributo
Page 50: 3.6 Description of terminals of tro
Page 54: Symbol Function Description S1 S2 S
Page 58: (3) Frame3:Three phase JNTHBCBA__BC
Page 62: 3-22 Chapter 3 Ambient Environment
Page 68: 4.1.2 Operation Instruction of the
Page 72: 4.1.4 Operation Instruction of the
Page 76: Example4. Modify the Frequency in O
Page 80: Chapter 4 Software Index 4. When pa
Page 84: 1-06 (Frequency Source) 1-07 (Keypa
Page 88: 3-23 (Center F of Trav) Center Freq
Page 92: Chapter 4 Software Index 5-08 (Stop
Page 96: 9-03 (Trip DEC Level) 9-04 (Trip RU
Page 100: 11-7 (Output Filter T) Output Lag F
Page 104: 4.4 Parameter Function Description
Page 108: Chapter 4 Software Index 1-01 = 000
Page 112: Parameter Group 2 - Manual/Automati
Page 116:
Chapter 4 Software Index 190V(220V
Page 120:
4-29 3-15 3-14 3-13 3-17: Parameter
Page 124:
Chapter 4 Software Index traverse r
Page 128:
Parameter Group 4 - Digital Display
Page 132:
Chapter 4 Software Index 3. 5-00~06
Page 136:
Operation UP DOWN Output 6-00 Frequ
Page 140:
the following graph). 4-39 Chapter
Page 144:
4-41 Chapter 4 Software Index Param
Page 148:
time will increase accordingly. 4-4
Page 152:
8-04: Frequency Reached Output Sett
Page 156:
8-02/3 = 04: Frequency detection Fo
Page 160:
Chapter 4 Software Index action lev
Page 164:
2. 10-0 = 0 - 17 V / F Pattern (Ref
Page 168:
11-0: PID Operation Selection Param
Page 172:
4-55 Chapter 4 Software Index Param
Page 176:
Chapter 4 Software Index 1.RS-485 C
Page 180:
Chapter 4 Software Index On the con
Page 184:
4.5.2 Function of Basic Instruction
Page 188:
Sample: Input under the Ladder Prog
Page 192:
Timer 2 3 1 4 5 6 (1) Timer Mode 1
Page 196:
(3) Timer Mode 3 (OFF-Delay A Mode)
Page 200:
Analog comparator 1 2 3 4 6 Analog
Page 204:
1 2 3 4 Sample: 5 6 7 8 Input under
Page 208:
Chapter 5 Troubleshooting and maint
Page 212:
5.1.4 Special conditions Display Er
Page 216:
Page 220:
5.3 Quick troubleshooting of 7300CV
Page 224:
Troubleshooting for OC, OL error di
Page 228:
The motor can not run YES Is MCCB a
Page 232:
Page 236:
Chapter 6 Peripherals Components Ch
Page 240:
6.4 Digital operator and extension
Page 244:
6. 5 EMC Filter Chapter 6 Periphera
Page 248:
FS 6147 - 39 - 07 FS 6149 - 28 - 07
Page 252:
RS-232 1.8m THREE-PHASE POWER SUPPL
Page 256:
Appendix 1: 7300CV Motor Internal P
Page 260:
Appendix 2: 7300CV parameter settin
show all

CV7300 Instruction Manual - TECO-Westinghouse Motor Company

Create successful ePaper yourself

Delete template?

Save as template?