Alternative Support Systems for Cantilever - National Transportation ...

More documents

Recommendations

Info

Bolt Properties - D1" ASTM A325 plate Center to Center Radius of Bolts rb := 12in Number of Bolts No_Bolts := 12 Field Strength of Bolts fy_bolt_field := 55ksi Ultimate Strength of Bolts fu_bolt := 105ksi Dpipe Radius of the pipe rp := = 10 in 2 Diameter of the bolt dbolt := 1.50in Bolt Bearing Strength Lc := ( ) ϕshear := .75 Bp − db − .5⋅dbolt 2 = 1.62 in ϕRn := 1.2⋅Fu_plate⋅Lc⋅ tplate ϕRn = 120.9 kip Rn_parallel := 2⋅ϕRn Rn_parallel = 241.8 kip ⎛ ⎜ ⎝ ⎞ ⎟ ⎠ db Tn_bolt_bearing := No_Bolts⋅Rn_parallel⋅ T 2 n_bolt_bearing 2.42 10 3 = × ft·kip Check_Bolt_Bearing := "Sufficient Strength" if Tn_bolt_bearing ≥ Tn_blowout Check Bolt Spacing sreq := 2.67⋅dbolt = 4 in sactual := π⋅db 12 = 5.24 in "Insufficient Strength" otherwise Check_Bolt_Bearing = "Sufficient Strength" Check_Bolt_Spacing := "Sufficient" if sactual ≥ sreq Check_Bolt_Spacing = "Sufficient" Check Bolt Shear ( ) 2 Ab π ⋅ .5⋅dbolt 1.77 in 2 := = Fnv := .4⋅120ksi = 48 ksi ϕVn := ϕshear⋅Ab⋅ Fnv "Insufficient" otherwise ϕVn = 63.62 kip Vn_parallel := ϕVn⋅2 Vn_parallel = 127.23 kip ⎛ ⎜ ⎝ ⎞ ⎟ ⎠ db Tbolt_shear := No_Bolts⋅Vn_parallel⋅ T 2 bolt_shear 1.27 10 3 = × ft·kip 124
Check_Bolt_Shear := "Sufficient Strength" if Tbolt_shear ≥ Tn_blowout Weld Design "Insufficient Strength" otherwise Weld Connecting Annular Plate to Pipe tpipe = 0.47 in Check_Bolt_Shear = "Sufficient Strength" 3 Weld_Size 8 in := AISC Spec. J2 Table J2.4 Felectrode := 70ksi FW := .6⋅Felectrode AISC Spec. J2 Table J2.5 Throat := .707⋅Weld_Size Rn_weld := Throat⋅FW Rn_weld 11.14 kip = ⋅ in Rn_yield := .6⋅Fy_pipe⋅tpipe Rn_yield 11.72 kip = ⋅ in Rn_rupture := .45⋅Fu_pipe⋅tpipe Rn_rupture 12.14 kip = ⋅ in Rn := min( Rn_weld, Rn_yield, Rn_rupture) Rn 11.14 kip = ⋅ in Rweld := Rn⋅π⋅d pipe Rweld = 559.72 kip dpipe Tweld := Rweld⋅ T 2 weld = 373.15 ft·kip dpipe Mweld := Rweld⋅ M 2 weld = 373.15 ft·kip Base Connection Tn_s_pipe = 359.1 ft·kip Tweld = 373.15 ft·kip Mweld = 373.15 ft·kip 125
Page 1 and 2:
Report No. BDK75 977-04 Date: Augus
Page 3 and 4:
Metric Conversion Table SYMBOL WHEN
Page 5 and 6:
ALTERNATIVE SUPPORT SYSTEMS FOR CAN
Page 7 and 8:
EXECUTIVE SUMMARY During the 2004 h
Page 9 and 10:
CHAPTER TABLE OF CONTENTS 1 INTRODU
Page 11 and 12:
Torsion Test Data .................
Page 13 and 14:
LIST OF FIGURES Figure page Figure
Page 15 and 16:
Figure 4-15. Arrangement of the LVD
Page 17 and 18:
CHAPTER 1 INTRODUCTION This project
Page 19 and 20:
CHAPTER 2 BACKGROUND The following
Page 21 and 22:
information obtained in the late 19
Page 23 and 24:
these problems. The concern with fa
Page 25 and 26:
opposite side, see Figure 2-2 The s
Page 27 and 28:
2.2.4 Helical Pipes This option wou
Page 29 and 30:
2.3 Alternative Foundations from Ot
Page 31 and 32:
Figure 2-10. Drilled concrete piles
Page 33 and 34:
Figure 2-13. Grouted soil anchors G
Page 35 and 36:
The pad and pier foundation, found
Page 37 and 38:
comments and recommendations on pre
Page 39 and 40:
CHAPTER 3 DESIGN IMPLICATIONS Based
Page 41 and 42:
Figure 3-2. Differences between con
Page 43 and 44:
2 [ ] 2 2 ( r ) + 3. 25 ( r ) − (
Page 45 and 46:
eakout surface for a single plate,
Page 47 and 48:
strength of a headed anchor in tens
Page 49 and 50:
Figure 3-9. Schematic of anticipate
Page 51 and 52:
Vbfp l e tfp bfp f’c ca1 = the ba
Page 53 and 54:
3.2.2 Equivalent Side-Face Blowout
Page 55 and 56:
computed. See Equation 3-14 below t
Page 57 and 58:
One method to quantify the failure
Page 59 and 60:
• An additional 12-4.5” long, 1
Page 61 and 62:
Applied load Lever arm Figure 4-4.
Page 63 and 64:
Figure 4-8. Isometric view of embed
Page 65 and 66:
Flexural plate breakout area Torsio
Page 67 and 68:
4.2.4 Annular Base Plate Design The
Page 69 and 70:
torsional strength of the lever arm
Page 71 and 72:
4.4 Concrete Block and Tie-Down Des
Page 73 and 74:
Figure 4-13. Arrangement of the LVD
Page 75 and 76:
4.7 Summary of Torsion and Flexure
Page 77 and 78:
foundation displayed the predicted
Page 79 and 80:
Figure 5-5. Specimen at failure 5.1
Page 81 and 82:
Figure 5-7. Torsional moment and ro
Page 83 and 84:
torsional 45 degree crack formation
Page 85 and 86:
Figure 5-11. Widening of concrete b
Page 87 and 88:
Failure cracks widen Bond loosens F
Page 89 and 90: Rear of shaft Figure 5-14. Load and
Page 91 and 92: testing, signifying that the predic
Page 93 and 94: provided in NCHRP Report 412 were i
Page 95 and 96: 6.2.2 Tapered Embedded Steel Pipe a
Page 97 and 98: Figure 6-3. FDOT Design Standards I
Page 99 and 100: This option provides a possible alt
Page 101 and 102: 6.2.5 Cast-in-Place Solid Concrete
Page 103 and 104: This option does have some disadvan
Page 105 and 106: Figure 6-9. Embedded steel pipe and
Page 107 and 108: However, the fillet welds are susce
Page 109 and 110: APPENDIX A TEST APPARATUS DRAWINGS
Page 111 and 112: Figure A-3. Dimensioned side elevat
Page 113 and 114: Figure A-5. Dimensioned drawings of
Page 115 and 116: Figure A-7. Dimensioned plan drawin
Page 117 and 118: Figure A-9. Dimensioned drawing of
Page 119 and 120: Figure A-11. Dimensioned view of em
Page 121 and 122: STIFFENER DESIGN Calculation of Cap
Page 123 and 124: L breakout Concrete Breakout Equiva
Page 125 and 126: Abrg L⋅b 7 in 2 := = .5 Nsb 200
Page 127 and 128: β 1 f c Calculations Using ACI Str
Page 129 and 130: Determine Flexural Capacity of Roun
Page 131 and 132: DEVELOPMENT LENGTHS OF FLEXURAL REI
Page 133 and 134: Short Pipe Design Flexural Strength
Page 135 and 136: Long Pipe Design Flexural Strength
Page 137 and 138: Superstructure Assembly Strength -
Page 139: Weld Design Tn_blowout Vweld := Tor
Page 143 and 144: Check Reinforcement No_Bars_Block_R
Page 145 and 146: Tie-Down Design Block Properties Wi
Page 147 and 148: Vmax Total Load that the Tie-down m
Page 149 and 150: λpf := .38⋅ λpw := 3.76⋅ E F
Page 151 and 152: Input and Properties Shaft Torsion
Page 153 and 154: ψcV := 1.4 ψecV := 1.0 ψedV := 1
Page 155 and 156: lbreakout := L + 2⋅1.5ca1 lbreako
Page 157 and 158: Rn_weld := Throat⋅FW Rn_weld 11.1
Page 159 and 160: ⎛ ⎜ ⎜⎜⎜⎜⎜⎜⎜ 9.250
Page 161 and 162: Flexural Capacity of T-Plates Using
Page 163 and 164: FAILURE EQUATIONS Torsion Threshold
Page 165 and 166: Required Length of Shaft Based on B
Page 167 and 168: Design Axial Strength ϕcomp := .90
Page 169 and 170: Design Axial Strength ϕcomp := .90
Page 171 and 172: Zp := ⎛ ⎜ ⎝ bp tp⋅ 2 ⎞
Page 173 and 174: Bolt Properties - D1" ASTM A325 Cen
Page 175 and 176: CONCRETE BLOCK Concrete Block Desig
Page 177 and 178: Check Shear Check_Shear_B := "Suffi
Page 179 and 180: 7'-4" 8" 5'-4" 8" 1'-3" Calculate s
Page 181 and 182: Required Capacity of the Channel As
Page 183 and 184: Check_Flange_Compact_Unit := "Compa
Page 185 and 186: Rear of Shaft Face of Shaft Figure
Page 187 and 188: Bolt slippage ends Predicted failur
Page 189 and 190: APPENDIX D DESIGN GUIDELINES For th
Page 191 and 192:
The designer should then use this i
Page 193 and 194:
• Determine the angle required fo
Page 195 and 196:
Superstructure Base Connection Foun
Page 197 and 198:
1.5ca1 1.5ca1 Length of bearing are
Page 199 and 200:
Vu = 9.04 kip T .u = 198.88 ft·kip
Page 201 and 202:
Increase threaded rod diameter to 2
Page 203 and 204:
Embedded Pipe and Torsion Plates De
Page 205 and 206:
⎝ ⎠ Check_Breakout_Torsion := "
Page 207 and 208:
Lbreakout := tflex.plate + 2⋅1.5c
Page 209 and 210:
( ) .85 if fc < 4000psi β 1 f c .6
Page 211 and 212:
REFERENCES 1. Cook, R.A., and Halco
show all

Alternative Support Systems for Cantilever - National Transportation ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?