Girard Systems- Warranty and Freight Procedures

More documents

Recommendations

Info

Loosen front bolt Pivot bolt / ~,?-Q~~"l r Screw FIGURE 7 LOOSEN PIVOT BOLT HEIGHT ADJUSTMENT OF ARMS Tools Required: -0 19mm (3/4") Open end wrench -0 10mm (3/8") Open end wrench This adjustment may be required if, as the awning Lead Rail closes into the awning casing, the 'elbow' of one ofthe arms is hanging downward, hitting the bottom ofthe casing. This adjustment is usually required after an arm replacement 1) Open the awning about 18 inches. 2) Atthe selected arm, loosen the (2) locknuts located atthe side ofthe upper arm connection using a 19mm (3/4") open-end wrench. 3) See exploded view and Figure 7. Locate the smaller adjustment bolt located directly under the rearlocknutthatwasjustloosened. Place a 10mm (3/8") open-endwrench around the bolt head, and rotate the wrench in a TIGHTEN (clockwise direction) to raise the arm. Slight rotation is all that is necessary; Likewise, LOOSENING (counter clockwise direction) the bolt will lower the arm. As this adjustment is being performed, keep in mindthat after re-tightening the locknuts, the arm will rise slightly higher. 4) Tighten the (2) locknuts located on the side ofthe arm connection. 5) Close the awning completely, and check for proper fit. 16 Girard Systems © 2005
--------------- GIRARD SYSTEMs" Adjustment Bolt FIGURE 8 ADJUSTMENT BOLT ADJUSTING LEAD RAIL Pitch Angle Screw 0/ FIGURE 9 PITCH OF LEAD RAIL WHEN CLOSED Girard Systems © 2005 17
Page 2 and 3: Girard Systems- Warranty and Freigh
Page 4 and 5: WARRANTY Girard Systems offers a Li
Page 6 and 7: Remote Switch 46 (Hardware Installa
Page 8 and 9: IMPORTANT OPERATION REMINDERS 1. Co
Page 10 and 11: B. REMOTE CONTROL (Programming) 1.
Page 12 and 13: FIGURE 3 RTS REMOTE SWITCH BATTERY
Page 14 and 15: GIRARD SYSTEMS G-2000/G-1500 ADJUST
Page 16 and 17: ADJUSTING MOTOR LIMIT SWITCHES (CON
Page 20 and 21: The awning lead rail comes factory
Page 22 and 23: SECTION I ACCESSING THE MOTOR Beave
Page 24 and 25: 2) Place one person in front ofthe
Page 26 and 27: I. FABRIC REPLACEMENT RECESSED AWNI
Page 28 and 29: During this fabric installation and
Page 30 and 31: Important Note: Extreme CAUTION sho
Page 32 and 33: ® GIRARD SYSTEMS G-2000Automatic L
Page 34 and 35: TOOLS REOUIRED --J --J --J --J --J
Page 36 and 37: INSTALLATION SEOUENCE 4.5 hours (ba
Page 38 and 39: ~ Diagram not to scale Minimum 51S"
Page 40 and 41: (- --:;':-,.>, 7/16" __ \. '\~:::::
Page 42 and 43: 2. Place awning onto brackets, ensu
Page 44 and 45: 3. Drill one 3/8" hole for anemomet
Page 46 and 47: 4. Ten feet (10') ofgray low-voltag
Page 48 and 49: Cl ~ ~ ~ ~~ @ ~ a ~ $ $ -. MOO _.l'
Page 50 and 51: --------------- GIRARD SYSTEMs" 1.
Page 52 and 53: --------------- GIRARD ACL current-
Page 54 and 55: -------------.,-~~ -""". -- .....~
Page 56 and 57: W. WEATHER STRIPPING (Installation)
Page 58 and 59: III. IV. MOTOR SPECIFICATIONS 1. Ty
Page 60 and 61: SOLUTION Open awning about three (3
Page 62 and 63: nuts located beside the arm connect
Page 64 and 65: PART NO. WHITE PART NO. BI ACK PART
Page 66 and 67: ,------ ,- @:~~-_llt-, , / ' , , I;
Page 68 and 69:
5 ~ 52 51 53 96 © 36~ 22 ~.~; .. \
show all

Girard Systems- Warranty and Freight Procedures

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?