ES4626-SFP Management Guide.pdf

More documents

Recommendations

Info

15.3.9 anti-arpscan trap enable Command:anti-arpscan trap enable no anti-arpscan trap enable Function:Enable ARP scanning prevention SNMP Trap function;” no anti-arpscan trap enable” command disable ARP scanning prevention SNMP Trap function. Parameters:None. Default Settings:Disable ARP scanning prevention SNMP Trap function Command Mode:Global configuration mode User <strong>Guide</strong>: After enabling ARP scanning prevention SNMP Trap function, users will receive Trap message whenever a port is closed or recovered by ARP scanning prevention, and whenever IP t is closed or recovered by ARP scanning prevention Example: Enable ARP scanning prevention SNMP Trap function of the switch Switch(Config)#anti-arpscan trap enable 15.3.10 show anti-arpscan Command:show anti-arpscan [trust |prohibited ] Function:Display the operation information of ARP scanning prevention function Parameters:None. Default Settings: Display every port to tell whether it is a trusted port and whether it is closed. If the port is closed, then display how long it has been closed. Display all the trusted IP and disabled IP. Command Mode:Admin Mode User <strong>Guide</strong>:Use “show anti-arpscan trust port” if users only want to check trusted ports. The reset follow the same rule. Example: Check the operating state of ARP scanning prevention function after enabling it. Switch(Config)#show anti-arpscan Total port: 36 Name Port-property beShut shutTime(seconds) Ethernet1/1 untrust N 0 Ethernet1/2 untrust N 0 Ethernet1/3 untrust N 0 Ethernet1/4 untrust N 0 Ethernet1/5 untrust N 0 394
Ethernet1/6 untrust N 0 Ethernet1/7 untrust N 0 Ethernet1/8 untrust N 0 Ethernet1/9 untrust N 0 Ethernet1/10 untrust N 0 Ethernet1/11 untrust N 0 Ethernet1/12 untrust N 0 Ethernet4/1 untrust N 0 Ethernet4/2 untrust N 0 Ethernet4/3 untrust N 0 Ethernet4/4 trust N 0 Ethernet4/5 untrust N 0 Ethernet4/6 supertrust N 0 Ethernet4/7 untrust Y 30 Ethernet4/8 trust N 0 Ethernet4/9 untrust N 0 Ethernet4/10 untrust N 0 Ethernet4/11 untrust N 0 Ethernet4/12 untrust N 0 Ethernet4/13 untrust N 0 Ethernet4/14 untrust N 0 Ethernet4/15 untrust N 0 Ethernet4/16 untrust N 0 Ethernet4/17 untrust N 0 Ethernet4/18 untrust N 0 Ethernet4/19 untrust N 0 Ethernet4/20 untrust N 0 Ethernet4/21 untrust N 0 Ethernet4/22 untrust N 0 Ethernet4/23 untrust N 0 Ethernet4/24 untrust N 0 Prohibited IP: IP shutTime(seconds) 1.1.1.2 132 Trust IP: 192.168.99.5 255.255.255.255 395
Page 1 and 2:
ES4624-SFP/ES4626-SFP L3 Gigabit Et
Page 3 and 4:
Content CHAPTER 1 SWITCH MANAGEMENT
Page 5 and 6:
2.10.7 Telnet server user configura
Page 7 and 8:
CHAPTER 6 MAC TABLE CONFIGURATION .
Page 9 and 10:
10.1.3 Commands for Layer 3 Interfa
Page 11 and 12:
15.3.4 anti-arpscan trust .........
Page 13 and 14:
17.9.3 MBGP4+ Examples.............
Page 15 and 16:
21.2.4 PIM-SM Typical Application..
Page 17 and 18:
CHAPTER 24 THE NUMBER LIMITATION FU
Page 19 and 20:
26.4 MRPP TYPICAL SCENARIO.........
Page 21 and 22:
ES4624-SFP/ES462 6-SFP Functional C
Page 23 and 24:
Copyright (c) 2001-2006 by Accton T
Page 25 and 26:
Step 2: Run Telnet Client program.
Page 27 and 28:
Step 2: Run HTTP protocol on the ho
Page 29 and 30:
CLI interface is familiar to most u
Page 31 and 32:
ethernet ethernetxx)# supported com
Page 33 and 34:
• vlan , parameter values are req
Page 35 and 36:
ES4624-SFP/ES4626-SFP switch shell
Page 37 and 38:
Chapter 2 Basic Switch Configuratio
Page 39 and 40:
Command: debug ssh-server no debug
Page 41 and 42:
Command: help Function: Output brie
Page 43 and 44:
2.1.1.16 language Command: language
Page 45 and 46:
VRF name: VPN Routing/Forwarding in
Page 47 and 48:
Function: Warm reset the switch. Co
Page 49 and 50:
terminal. If this command is config
Page 51 and 52:
can’t exceed 16 characters; Comma
Page 53 and 54:
Global Mode ip telnet server no ip
Page 55 and 56:
Switch(Config)#telnet-server securi
Page 57 and 58:
is 768 to 2048. The default value i
Page 59 and 60:
on the path receives this datagram,
Page 61 and 62:
2.2.7.1.3 show history Command: sho
Page 63 and 64:
same. 2.2.7.1.9 show interface swit
Page 65 and 66:
Command mode: Admin Mode Usage Guid
Page 67 and 68:
Severity Value Description emergenc
Page 69 and 70:
example:Clear all information in th
Page 71 and 72:
Command ip address [secondary] no
Page 73 and 74:
2.4 SNMP Configuration 2.4.1 Introd
Page 75 and 76:
viewed and controlled by the suppor
Page 77 and 78:
] [notify ]] no snmp-server group
Page 79 and 80:
get-request PDUs Number of packets
Page 81 and 82:
command disables the switch to send
Page 83 and 84:
Command: show snmp group Function:
Page 85 and 86:
no snmp-server group {NoauthNopriv
Page 87 and 88:
Function: Configure to permit to ac
Page 89 and 90:
traps” command). and remember to
Page 91 and 92:
[Boot]: Step 3: Under BootROM mode,
Page 93 and 94:
establishes data connection on port
Page 95 and 96:
(1) Start TFTP server (2) Configure
Page 97 and 98:
press Enter,following hints will be
Page 99 and 100:
2.5.3.2.2.5 ftp-server timeout Comm
Page 101 and 102:
Switch 10.1.1.2 computer 10.1.1.1 F
Page 103 and 104:
user profile configuration files fr
Page 105 and 106:
331 User name okay, need password.
Page 107 and 108:
dosattack-check enable srcip-equal-
Page 109 and 110:
Usage Guide: By enabling this funct
Page 111 and 112:
2.6.3.7 dosattack-check icmp-attack
Page 113 and 114:
no jumbo enable Jumbo frames Disabl
Page 115 and 116:
the “no” form of this command r
Page 117 and 118:
Function: Configure the length of t
Page 119 and 120:
Sample packet max len is 1400 Sampl
Page 121 and 122:
TACACS+ terminal access controller
Page 123 and 124:
2.9.3.3 tacacs-server timeout Comma
Page 125 and 126:
prompts of command-line interface,
Page 127 and 128:
2.10.2.3 Configure IP address of SN
Page 129 and 130:
which has server file name is “no
Page 131 and 132:
• Show running-config-to display
Page 133 and 134:
2.10.6 Telnet server configuration
Page 135 and 136:
Command Interface Mode interface et
Page 137 and 138:
Both fiber and copper Copper Copper
Page 139 and 140:
Usage Guide: Run the exit command t
Page 141 and 142:
Switch(Config-If-Port-Range)#rate-l
Page 143 and 144:
1000Mbps at full-duplex mode; noneg
Page 145 and 146:
the optional parameter secondary is
Page 147 and 148:
3.2.3.2.2 interface ethernet Comman
Page 149 and 150:
another port. The duplicated port i
Page 151 and 152:
3.4 Port Configuration Example Swit
Page 153 and 154:
applied to port 1/1. Port list tabl
Page 155 and 156:
Click Port configuration, Port mirr
Page 157 and 158:
For Port Chansnel to work properly,
Page 159 and 160:
otherwise, the group will be delete
Page 161 and 162:
Number of ports in group Maxports N
Page 163 and 164:
port state LACP activety . 1 LACP t
Page 165 and 166:
SwitchA SwitchB Fig 4-2 Configuring
Page 167 and 168:
“on” mode is completely joined
Page 169 and 170:
Chapter 5 VLAN Configuration 5.1 VL
Page 171 and 172:
Command Interface Mode switchport t
Page 173 and 174:
Ethernet ports their member ports.
Page 175 and 176:
access vlan” command deletes the
Page 177 and 178:
Switch(Config)#interface ethernet 1
Page 179 and 180:
Switch(Config-Vlan100)#switchport i
Page 181 and 182:
5.2.3.2 debug gvrp Command: debug g
Page 183 and 184:
Function: Display the global and po
Page 185 and 186:
Switch(Config-Vlan100)#switchport i
Page 187 and 188:
It is obvious that, the dot1q-tunne
Page 189 and 190:
Switch (Config-Ethernet1/10)#exit 5
Page 191 and 192:
ID to new VLAN ID according to the
Page 193 and 194:
Switch(Config-If-Ethernet4/1)#vlan-
Page 195 and 196:
description is as follows The MAC-b
Page 197 and 198:
Command Global Mode dynamic-vlan ma
Page 199 and 200:
with the IP protocol or else some a
Page 201 and 202:
Example: Display the port currently
Page 203 and 204:
Figure 5-5 Typical topology applica
Page 205 and 206:
Command Global Mode voice-vlan mac
Page 207 and 208:
Function: Configure the specified V
Page 209 and 210:
Chapter 6 MAC Table Configuration 6
Page 211 and 212:
time for MAC address entry in ES462
Page 213 and 214:
form to restore the aging-time to 3
Page 215 and 216:
1. Set the MAC address 00-01-11-11-
Page 217 and 218:
port-security violation {protect |
Page 219 and 220:
secure static MAC addresses must be
Page 221 and 222:
1 0000.0000.1111 SecureConfigured E
Page 223 and 224:
Chapter 7 MSTP Configuration 7.1 MS
Page 225 and 226:
egion to become the CST. The MSTI i
Page 227 and 228:
Command Global Mode spanning-tree m
Page 229 and 230:
Command Global Mode spanning-tree t
Page 231 and 232:
Command mode: MSTP Region Mode Defa
Page 233 and 234:
forward-time” restores the defaul
Page 235 and 236:
Switch(Config)#spanning-tree max-ho
Page 237 and 238:
Usage Guide: By setting the port co
Page 239 and 240:
Switch(Config-Ethernet-1/2)# 7.3.21
Page 241 and 242:
Route Cost Port 2 128 128 128 Port
Page 243 and 244:
SwitchD(Config-Vlan40)#exit SwitchD
Page 245 and 246:
7.5 MSTP Troubleshooting • In ord
Page 247 and 248:
Ethernet1/2 128.002 0 BLK ALTR 3276
Page 249 and 250:
Command: debug spanning-tree no deb
Page 251 and 252:
Set on port 1/1 route cost of the M
Page 253 and 254:
7.6.3.6 Set bridge priority of the
Page 255 and 256:
DSCP: Differentiated Services Code
Page 257 and 258:
Fig 8-4 Classification process Poli
Page 259 and 260:
Fig 8-6 Queuing and Scheduling proc
Page 261 and 262:
Command Global Mode policy-map no
Page 263 and 264:
queue mode wrr method; the “queue
Page 265 and 266:
Command Mode: Class-map Mode Usage
Page 267 and 268:
“ command. Example: Setting a pol
Page 269 and 270:
defines DSCP mark down mapping, whe
Page 271 and 272:
Example: Creating and deleting a po
Page 273 and 274:
set the default QoS value of the po
Page 275 and 276:
Switch(Config)#mls qos Switch(Confi
Page 277 and 278:
Command mode: Admin Mode Example: S
Page 279 and 280:
Classified In-profile out-profile T
Page 281 and 282:
to previously created classmap and
Page 283 and 284:
Chapter 9 Flow-based Redirection 9.
Page 285 and 286:
Examples: Switch(Config)# show flow
Page 287 and 288:
Global Mode interface vlan no inte
Page 289 and 290:
while obtaining a globally unique I
Page 291 and 292:
(1) Configure DAD neighbor query me
Page 293 and 294:
[no] ipv6 nd suppress-ra Forbid IPv
Page 295 and 296:
(5)Configure Tunnel 6to4 Relay Comm
Page 297 and 298:
directly for tunnel router. Example
Page 299 and 300:
Usage Guide:The minimum time interv
Page 301 and 302:
10.2.2.3.1.12 ipv6 neighbor Command
Page 303 and 304:
Parameter: is the ipv4 address of t
Page 305 and 306:
configure IPv4 address 192.168.3.1
Page 307 and 308:
ipv6 address 2002::2/64 ! interface
Page 309 and 310:
SwitchA(Config-if-Vlan2)#ipv4 addre
Page 311 and 312:
Frags: 0 reassembled, 0 timeouts 0
Page 313 and 314:
IPv6 ICMP: sent type Src Dst fro
Page 315 and 316:
ND RA MTU is 0 ND advertised reacha
Page 317 and 318:
Switch#show ipv6 neighbors IPv6 nei
Page 319 and 320:
ipv6 enable has been on IPv6 transm
Page 321 and 322:
10.4.2 URPF Operation Mechanism At
Page 323 and 324:
Parameter:None Usage Guide: Enable
Page 325 and 326:
10.5.3.2 clear arp-cache Command: c
Page 327 and 328:
Displayed information Total arp ite
Page 329 and 330:
DHCP packets so that the DHCP packe
Page 331 and 332:
ip dhcp excluded-address [] Exclud
Page 333 and 334:
Function: Configures default gatewa
Page 335 and 336:
Switch(dhcp-1-config)#host 10.1.128
Page 337 and 338:
Example: Setting the lease of DHCP
Page 339 and 340:
configuration as well as various co
Page 341 and 342:
4. Disable DHCP relay from forwardi
Page 343 and 344: Switch(Config-If-Vlan1)#ip helper-a
Page 345 and 346: Switch(dhcp-A1-config)#client-name
Page 347 and 348: 11.5.1.1 show ip dhcp binding Comma
Page 349 and 350: Message Received Statistics for DHC
Page 351 and 352: 11.6.1.5 Client WINS server configu
Page 353 and 354: 11.6.1.9 Excluded address Click DHC
Page 355 and 356: 11.6.2.5 Show conflict-logging Clic
Page 357 and 358: SubOpt: the sequence number of sub-
Page 359 and 360: ip dhcp relay information policy {d
Page 361 and 362: Switch(Config)#service dhcp Switch(
Page 363 and 364: Vlan2: Vlan3: ip dhcp relay informa
Page 365 and 366: pool { range 192.168.102.21 192.168
Page 367 and 368: Chapter 13 DHCP snooping Configurat
Page 369 and 370: Command Globe mode ip dhcp snooping
Page 371 and 372: 13.2.2.1 debug ip dhcp snooping pac
Page 373 and 374: Command:ip dhcp snooping binding us
Page 375 and 376: mutually exclusive to“ ip dhcp sn
Page 377 and 378: is relative to the type of the swit
Page 379 and 380: Ethernet1/16 untrust none 0second 0
Page 381 and 382: port maxnum of alarm info The max n
Page 383 and 384: Chapter 14 SNTP Configuration 14.1
Page 385 and 386: 14.2.3 sntp poll Command: sntp poll
Page 387 and 388: 14.4.2 Request interval configurati
Page 389 and 390: 3. Configure trusted ports 4. Confi
Page 391 and 392: Command:anti-arpscan port-based thr
Page 393: Default Settings:Enable the automat
Page 397 and 398: In the network topology above, port
Page 399 and 400: There are many sniff, monitor and a
Page 401 and 402: Function : Forbid ND automatic lear
Page 403 and 404: Fig 16-1 Prevent ARP ,ND Spoofing E
Page 405 and 406: Chapter 17 Routing Protocol 17.1 Ro
Page 407 and 408: Static route 1 RIP 120 OSPF ASE 150
Page 409 and 410: matching conditions for Community-l
Page 411 and 412: 3. Define the match clause in route
Page 413 and 414: set vpnv4 next-hop no set vpnv4 ne
Page 415 and 416: here can define a “permit 0.0.0.0
Page 417 and 418: 17.2.3.7 match metric Command: matc
Page 419 and 420: The check sequence among nodes is i
Page 421 and 422: 17.2.3.16 set community Command: se
Page 423 and 424: compared. To extend the comparison
Page 425 and 426: Switch#config terminal Switch(confi
Page 427 and 428: mode items can be defined first to
Page 429 and 430: Set clauses: metric 10 Displayed in
Page 431 and 432: no ip route { | /} [ | ] [] Functi
Page 433 and 434: network, mask, next-hop address, in
Page 435 and 436: Switch(config)#ip route 10.1.1.0 25
Page 437 and 438: The Layer3 switch modifies its loca
Page 439 and 440: protocols to be introduced in RIP)
Page 441 and 442: 5)configure the split horizon Comma
Page 443 and 444: address-family ipv4 vrf no address
Page 445 and 446:
ospf only delete OSPF routes from t
Page 447 and 448:
Example: Switch# config terminal Sw
Page 449 and 450:
Function: Set the password used in
Page 451 and 452:
Default: Version 2 Command Mode: In
Page 453 and 454:
statistics command. Example: Switch
Page 455 and 456:
17.4.3.28 redistribute Command: red
Page 457 and 458:
is the valid period of the key in s
Page 459 and 460:
SwitchA(Config-Vlan2)# switchport i
Page 461 and 462:
SwitchA(config-router-af)#network V
Page 463 and 464:
Default redistribution metric is 1
Page 465 and 466:
Parameter: Specifies the name of VP
Page 467 and 468:
17.5 RIPng 17.5.1 Introduction to R
Page 469 and 470:
1. Enable RIPng protocol (required)
Page 471 and 472:
[no] [] offset-list {in|out} Conf
Page 473 and 474:
Default: No default configuration C
Page 475 and 476:
Usage Guide:The command can configu
Page 477 and 478:
Command Mode: Router mode Example:
Page 479 and 480:
17.5.5 RIPng Troubleshooting The RI
Page 481 and 482:
3000:1:1::1/64 fe80::203:fff:fe01:4
Page 483 and 484:
17.6 OSPF 17.6.1 Introduction to OS
Page 485 and 486:
andwidth required in the network. O
Page 487 and 488:
3)Configure the cost for sending pa
Page 489 and 490:
ip ospf transit-delay no ip ospf t
Page 491 and 492:
Parameter: is the area number whic
Page 493 and 494:
Command: area range [advertise| n
Page 495 and 496:
AUTH_KEY= authentication-key : A p
Page 497 and 498:
17.6.3.13 distance Command: distanc
Page 499 and 500:
cancels the authentication Paramete
Page 501 and 502:
17.6.3.21 ip ospf disable all Comma
Page 503 and 504:
notation Default: Check mtu size in
Page 505 and 506:
Command Mode: Interface Mode Usage
Page 507 and 508:
Usage Guide: For Specifying the rea
Page 509 and 510:
oute-map point to the probe of the
Page 511 and 512:
tag is the identification label of
Page 513 and 514:
SwitchB(config-if-vlan3)#no shut-do
Page 515 and 516:
SwitchA0 and Switch11, and network
Page 517 and 518:
SwitchB(config-If-Vlan2)#ip ospf au
Page 519 and 520:
SwitchB Interface vlan1:10.1.1.1/24
Page 521 and 522:
areas should only be connected to o
Page 523 and 524:
17.6.5.1.8 show ip ospf Command: sh
Page 525 and 526:
Function: Display the OSPF link sta
Page 527 and 528:
192.168.1.1 1 Full/Backup 00:00:32
Page 529 and 530:
Routing Protocol is "bgp 0" Outgoin
Page 531 and 532:
switches to form a link-state datab
Page 533 and 534:
1. Enable OSPFv3 (required) (1) Ena
Page 535 and 536:
IPv6 ospf dead-interval [instance-
Page 537 and 538:
area or NSSA area Example: Set the
Page 539 and 540:
Example: Switch#config terminal Swi
Page 541 and 542:
Switch#config terminal Switch(confi
Page 543 and 544:
packet is not received within the i
Page 545 and 546:
Example: Switch#config terminal Swi
Page 547 and 548:
(assume vlan2 interface of layer3 S
Page 549 and 550:
SwitchD(config-if-vlan2)#exit Confi
Page 551 and 552:
Command Mode: Admin mode and global
Page 553 and 554:
Network-LSA (Area 0.0.0.0) Network
Page 555 and 556:
Default: Not displayed Command Mode
Page 557 and 558:
BGP stands for a Border Gateway Pro
Page 559 and 560:
• EBGP:External BGP When BGP runs
Page 561 and 562:
9.Adjust BGP Announcement Interval
Page 563 and 564:
neighbor {|} distribute-list {||} {
Page 565 and 566:
aggregate-address [summary-only] [
Page 567 and 568:
neighbor peer-group no neighbor
Page 569 and 570:
oute-map {in | out} route-map {in
Page 571 and 572:
13. Configure BGP routing redistrib
Page 573 and 574:
gp always-compare-med no bgp always
Page 575 and 576:
[as-set]: Show AS on the path in li
Page 577 and 578:
Function:Compare route ID; the “n
Page 579 and 580:
Switch(config-router)# bgp confeder
Page 581 and 582:
Usage Guide: This command is usuall
Page 583 and 584:
1771, namely not checking the AS in
Page 585 and 586:
different parameters (such as addre
Page 587 and 588:
Switch(config-af)#route-target both
Page 589 and 590:
command is for setting the route wh
Page 591 and 592:
when transmitting the BGP route in
Page 593 and 594:
originating side will then send an
Page 595 and 596:
Usage Guide: Configure the policies
Page 597 and 598:
: AS-PATH access-list name configur
Page 599 and 600:
no neighbor {|} override-capability
Page 601 and 602:
17.8.3.61 neighbor prefix-list Comm
Page 603 and 604:
Switch(config)#route-map test permi
Page 605 and 606:
Function: Disconnect the neighbor c
Page 607 and 608:
connection. The hold time is the ti
Page 609 and 610:
17.8.3.77 neighbor weight Command:
Page 611 and 612:
: Character string which is the nam
Page 613 and 614:
*>i100.1.1.0/24 10.1.1.68 0 100 0 2
Page 615 and 616:
SwitchB(config-router-bgp)#redistri
Page 617 and 618:
SwitchA AS100 vlan1:11.1.1.1 AS300
Page 619 and 620:
AS200 SwitchH vlan1:8.8.8.8 SwitchG
Page 621 and 622:
Metric=0 AS100 SwitchA vlan1:4.4.4.
Page 623 and 624:
importing routes. Direct-link route
Page 625 and 626:
17.8.5.1.4 show ip bgp community-in
Page 627 and 628:
Min penalty (floor) : 375 Total num
Page 629 and 630:
17.8.5.1.10 show ip bgp paths Comma
Page 631 and 632:
Network Next Hop Metric LocPrf Weig
Page 633 and 634:
Parameter: : Name of BGP instance :
Page 635 and 636:
SwitchC vlan1:2002::3 vlan2:2003::3
Page 637 and 638:
Chapter 18 IGMP Snooping 18.1 Intro
Page 639 and 640:
18.3 Commands for IGMP Snooping 18.
Page 641 and 642:
vlan query command, i.e. either sn
Page 643 and 644:
Example: Switch(config)#ip igmp sno
Page 645 and 646:
Multicast Router Group 1 Group 2 Sw
Page 647 and 648:
messages Command Mode:Admin Mode Us
Page 649 and 650:
Chapter 19 Multicast VLAN 19.1 Intr
Page 651 and 652:
enabled on a switch. Examples: Swit
Page 653 and 654:
Chapter 20 IPv4 Multicast Protocol
Page 655 and 656:
224.0.0.14 RSVP Encapsulation 224.0
Page 657 and 658:
Multicast transmission table entry
Page 659 and 660:
20.2.3.1 ip pim accept-register Com
Page 661 and 662:
hello_holdtime is configured but le
Page 663 and 664:
Switch (config)# 20.2.3.10 ip pim s
Page 665 and 666:
“no debug pim timer sat” comman
Page 667 and 668:
Usage Guide: Display the PIM buffer
Page 669 and 670:
20.2.5.1.7 show ip mroute case. It
Page 671 and 672:
(3) SPT Switch When the Multicast r
Page 673 and 674:
ip pim bsr-candidate {vlan | }[ ][
Page 675 and 676:
and is used to configure PIM-SM inf
Page 677 and 678:
hello-interval” command restores
Page 679 and 680:
created, this connection can’t be
Page 681 and 682:
command modifies Keepalive-period v
Page 683 and 684:
no ip pim ssm Function: Configure t
Page 685 and 686:
Switch (Config)# ip pim bsr-candida
Page 687 and 688:
Switch# debug ip pim event Switch#
Page 689 and 690:
debug pim timer hello ht debug pim
Page 691 and 692:
10.1.4.3 Vlan1 0 v2/S 1 1 10.1.4.3
Page 693 and 694:
10.1.4.3 Vlan3 00:00:17/00:01:29 v2
Page 695 and 696:
20.4 DVMRP 20.4.1 Introduction to D
Page 697 and 698:
Prune/Graft 4、 Configure DVMRP tu
Page 699 and 700:
Command Mode: Interface Configurati
Page 701 and 702:
20.4.4 DVMRP Configuration Examples
Page 703 and 704:
prune[prune-expiry-timer|prune-retx
Page 705 and 706:
20.4.5.1.5 show ip dvmrp pr Command
Page 707 and 708:
consequently guarantee the transmis
Page 709 and 710:
Global Configuration Mode [no] acce
Page 711 and 712:
not 0.0.0.0/0 in other access-list.
Page 713 and 714:
20.5.3.5 ip multicast destination-c
Page 715 and 716:
20.5.3.9 ip multicast source-contro
Page 717 and 718:
ip multicast destination-control is
Page 719 and 720:
to save all relationships of all ho
Page 721 and 722:
2)Configure the maximum response ti
Page 723 and 724:
20.6.3 Commands for IGMP 20.6.3.1 i
Page 725 and 726:
Parameter: : is group address Defau
Page 727 and 728:
or not; that is, if configuring the
Page 729 and 730:
Parameter: None Default: Disabled C
Page 731 and 732:
Source Address V3 Exp Fwd Flags gro
Page 733 and 734:
the multicast-forwarding item (S, G
Page 735 and 736:
21.1.3.1 ipv6 pim accept-register C
Page 737 and 738:
configure tunnel carefully. Example
Page 739 and 740:
no ipv6 pim state-refresh originati
Page 741 and 742:
21.1.5.1.2 debug ipv6 pim timer srt
Page 743 and 744:
Num Ifindex Name Addr 2000:1:111::1
Page 745 and 746:
case. It can check interface inform
Page 747 and 748:
(2) Multicast Source Registration W
Page 749 and 750:
Configure the value of holdtime dom
Page 751 and 752:
is used to configure PIM-SM informa
Page 753 and 754:
modified to 3.5*hello_interval, oth
Page 755 and 756:
Example: Configure vlan’s pim nei
Page 757 and 758:
Usage Guide: If this value is confi
Page 759 and 760:
Command Mode: Global Mode Usage Gui
Page 761 and 762:
Switch (Config-If-Vlan2) # ipv6 add
Page 763 and 764:
Default: Disabled Command Mode: Adm
Page 765 and 766:
no debug ipv6 pim timer hello ht no
Page 767 and 768:
Parameter: None Default: None Comma
Page 769 and 770:
Ver DR Priority/Mode Pim version ,v
Page 771 and 772:
Info source Priority Source of Boot
Page 773 and 774:
ipv6 mld query-interval no ipv6 ml
Page 775 and 776:
host-query messages periodically. T
Page 777 and 778:
Function: Configure the sources of
Page 779 and 780:
21.3.4 MLD Typical Application As s
Page 781 and 782:
Usage Guide: This switch can be ena
Page 783 and 784:
21.4.2 MLD Snooping Configuration T
Page 785 and 786:
snooping” command disables MLD Sn
Page 787 and 788:
21.4.3.7 ipv6 mld snooping vlan mro
Page 789 and 790:
Parameter: vlan-id: vlan id, valid
Page 791 and 792:
Command: show mac-address-table mul
Page 793 and 794:
Fig 16-5 Switches as MLD Querier Fu
Page 795 and 796:
There are two access-list actions a
Page 797 and 798:
access-list {deny | permit} igmp {
Page 799 and 800:
Creates an extended [no] {deny | pe
Page 801 and 802:
[no]{deny|permit}{any-source-mac|{h
Page 803 and 804:
access-list{deny|permit}{any-source
Page 805 and 806:
[no]{deny|permit}{any-source-mac|{h
Page 807 and 808:
[no]absolute-periodic{Monday|Tuesda
Page 809 and 810:
Make configurations effective withi
Page 811 and 812:
34(0x22): IGMP V3 REPORT packet 19(
Page 813 and 814:
{any-destination-mac|{host-destinat
Page 815 and 816:
Command Mode: Global mode Default C
Page 817 and 818:
Examples: Create a name extended IP
Page 819 and 820:
no entry will be created Example: C
Page 821 and 822:
} | any-destination | {host-destina
Page 823 and 824:
untagged-802-3 format of untagged e
Page 825 and 826:
of TCP/UDP source interface No., In
Page 827 and 828:
Functions: Create the name of time-
Page 829 and 830:
access-list 100 deny ip any any-des
Page 831 and 832:
Parameters: word assign name of tim
Page 833 and 834:
22.5.3 Configure the numeric extend
Page 835 and 836:
• Operation type -Add or Remove T
Page 837 and 838:
Chapter 23 802.1x Configuration 23.
Page 839 and 840:
needing to access the LAN via the a
Page 841 and 842:
Protocol Version: Represents the ve
Page 843 and 844:
The authentication can either be st
Page 845 and 846:
Fig 23-9 the Authentication Flow of
Page 847 and 848:
design of protocol and security is
Page 849 and 850:
access the network, while the other
Page 851 and 852:
3) Configure RADIUS Service paramet
Page 853 and 854:
Global Mode dot1x max-req no dot1x
Page 855 and 856:
Command mode: Global Mode Parameter
Page 857 and 858:
enabled on the port, or the port is
Page 859 and 860:
Default: The default maximum user a
Page 861 and 862:
Command: dot1x re-authentication no
Page 863 and 864:
switch will send accounting packets
Page 865 and 866:
etransmission count reaches the ret
Page 867 and 868:
Fig 23-14 User Joining Guest VLAN A
Page 869 and 870:
authentication-triggering messages
Page 871 and 872:
23.5.1.2 debug dot1x Command: debug
Page 873 and 874:
.Udp Port = 1813 .Is Primary = 0 .I
Page 875 and 876:
Global 802.1x Parameters Global 802
Page 877 and 878:
23.6.1.2 RADIUS authentication conf
Page 879 and 880:
• EAP relay authentication mode -
Page 881 and 882:
• Authentication type -Authentica
Page 883 and 884:
Limiting the number of MAC and ARP
Page 885 and 886:
show mac-address dynamic count {vla
Page 887 and 888:
Enable the number limitation functi
Page 889 and 890:
Switch(Config-if-Vlan1)#no ip arp d
Page 891 and 892:
Switch(Config)# show arp-dynamic co
Page 893 and 894:
dynamic nd and the number of nd on
Page 895 and 896:
24.4 The Number Limitation Function
Page 897 and 898:
Chapter 25 VRRP Configuration 25.1
Page 899 and 900:
Configures the simple authenticatio
Page 901 and 902:
Example: Configuring vrrp monitor i
Page 903 and 904:
Priority is always 254 for IP Owner
Page 905 and 906:
25.4 Typical VRRP Scenario As shown
Page 907 and 908:
Example: Enter created Virtual Rout
Page 909 and 910:
Chapter 26 MRPP Configuration 26.1
Page 911 and 912:
Packet Type Hello packet (Health ex
Page 913 and 914:
Enable Enable MRPP ring, format “
Page 915 and 916:
Switch(mrpp-ring-4000)#primary-port
Page 917 and 918:
Switch(Config)# mrpp ring 4000 Swit
Page 919 and 920:
nodes of MRPP ring, configures prim
Page 921 and 922:
Chapter 27 Cluster Configuration 27
Page 923 and 924:
Command Explanation Global Mode clu
Page 925 and 926:
address pool. The “no cluster ip-
Page 927 and 928:
Command: rcommand commander Functio
Page 929 and 930:
Parameter: is the interval of hear
Page 931 and 932:
command switch Command Mode: Admin
show all

ES4626-SFP Management Guide.pdf

Create successful ePaper yourself

Delete template?

Save as template?