Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

More documents

Recommendations

Info

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-330897.1 Media7.1.2 Detection Area of the Transmissive SensorThe Transmissive Sensor is movable from the centre to the left edge of media.The Transmissive Sensor detects a gap between labels, as illustrated below.Min. 2.0 mm(Min. 6.0 mm when usingthe cutter module.)Sensor position Area to be detected. Centre of mediaLabelGapLabelPrint sideMin. 12 mmMedia feed directionSensor is movablewithin this range.Sensor positionMin. 2.0 mmCentre of mediaPrint sideSquare holes(Round holes are not acceptable.)Min. 12 mmMedia feed directionSensor is movablewithin this range.NOTE:Round holes are not acceptable.E7- 3
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-330897.1 Media7.1.3 Detection Area of the Reflective SensorThe Reflective Sensor is movable from the centre to the left edge of media.The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm.The Reflective Sensor should be aligned with the centre of the Black Mark.Rectangular holes can substitute the black marks, on the condition that nothing is printed on the back side.Sensor should be positioned atthe centre of the black mark.Centre of mediaMin. 2.0 mmDetecting the blackmarks on the back.Min. 12 mmMedia feed directionSensor is movablewithin this range.7.1.4 Effective Print AreaThe figure below illustrates the relation between the head effective print width and media width.Out of print rangeOut of print range4 mm104 mm±0.2(Head Effective Print Range)120 mm (Max. media width)4 mmThe figure below shows the effective print area on the media.Area to be detected.Start line1.5 mm from theleft edge of media1mmGuaranteed print areaMedia height10 – 1500 mm1.5 mm from theright edge of media1mmMedia feed directionArea to be detected.Media width(backing paper width is not included.)NOTES:1. Be sure not to print on the 1.5-mm wide area from the media edges (shaded area in the above figure).Printing on this area may cause ribbon wrinkles, resulting in a poor print quality of the guaranteed printarea.2. The centre of media is positioned at the centre of the Print Head.3. Print quality in the 3-mm area from the print head stop position (including 1.5-mm non-printable area forprint speed slow down) is not guaranteed.E7- 4
Page 3 and 4:
TOSHIBA Barcode PrinterB-EX4T1 SERI
Page 10 and 11:
1. PRODUCT OVERVIEW ENGLISH VERSION
Page 12:
1. PRODUCT OVERVIEW ENGLISH VERSION
Page 15 and 16:
2. PRINTER SETUP ENGLISH VERSION EO
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: 2. PRINTER SETUP ENGLISH VERSION EO
Page 81 and 82: 2.PRINTER SETUPENGLISH VERSION EO1-
Page 83 and 84: 2.PRINTER SETUPENGLISH VERSION EO1-
Page 85 and 86: 3. ON LINE MODE ENGLISH VERSION EO1
Page 91 and 92: 4. MAINTENANCE ENGLISH VERSION EO1-
Page 93 and 94: 5. TROUBLESHOOTING ENGLISH VERSION
Page 99 and 100: 6. PRINTER SPECIFICATIONS ENGLISH V
Page 101: 7. SUPPLY SPECIFICATIONS ENGLISH VE
Page 105 and 106: 7. SUPPLY SPECIFICATIONS ENGLISH VE
Page 107 and 108: 7. SUPPLY SPECIFICATIONS ENGLISH VE
Page 109 and 110: APPENDIX 1 MESSAGES AND LEDSENGLISH
Page 111 and 112: APPENDIX 2 INTERFACEENGLISH VERSION
Page 117 and 118: APPENDIX 3 PRINT SAMPLESENGLISH VER
Page 123 and 124: APPENDIX 4 GLOSSARIESENGLISH VERSIO
show all

Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

Create successful ePaper yourself

Delete template?

Save as template?