Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

More documents

Recommendations

Info

APPENDIX 1 MESSAGES AND LEDSENGLISH VERSION EO1-33089APPENDIX 1 MESSAGES AND LEDSNOTES:• If a command error is found in the command received, up to 42 bytes of the erroneous command, starting from thecommand code, will be displayed. (However, [LF] and [NUL] will not be displayed.)Example 1[ESC]PC001;0A00,0300,2,2,A,00,B[LF][NUL]Command errorThe following message appears.SYNTAX ERRORPC001;0A00,0300,2,2,A,00,BExample 2[ESC]T20G30[LF] [NUL]Command errorThe following message appears.SYNTAX ERRORT20G30Example 3[ESC]PC002;0100,0300,15,15,A,00,00,J0101,+000000000A,Z10,P1[LF] [NUL]Command errorThe following message appears.SYNTAX ERRORPC002;0100,0300,15,15,A,00,00,J0101,+00000• When the error command is shown, “? (3FH)” appears for codes other than codes 20H to 7FH and A0H to DFH.• The battery level is not checked when the printer is reset or real time clock is not installed.• For details, please refer to the B-EX4T/EX6T Series External Equipment Interface Specification.EA1- 3
APPENDIX 2 INTERFACEENGLISH VERSION EO1-33089APPENDIX 2 INTERFACEAPPENDIX 2 INTERFACENOTE:To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements:• In case of a parallel interface cable or serial interface cable, fully shielded and fitted with metal or metallisedconnector housings.• Keep as short as possible.• Should not be bundled tightly with power cords.• Should not be tied to power line conduits.• A parallel interface cable to be used should conform to IEEE1284.• USB interface (Standard)Physical Layer: Conforming to V2.0 Full speedTransfer type: Control transfer, Bulk transferTransfer rate: Full speed (12M bps)Class:Printer classNumber of ports: 1Power source: Self powerConnector:Type BPin No. Signal1 VCC2 D-3 D+4 GNDSeries B Plug• LAN (Standard)Physical Layer: IEEE802.3 10BASE-T/100BASE-TXNumber of ports: 1Connector: RJ-45LED status: Link LED, Activity LEDLED LED Status LAN statusLink ON 10Mbps link or 100Mbps link is detected.Link LED (Green)OFF No link is detected.* Communication cannot be made while theLink LED is off.Activity LED (Orange)Activity ON CommunicatingOFF IdleLAN cable: 10BASE-T: UTP category 3 or category 5100BASE-TX: UTP category 5Cable length: Segment length Max. 100 mNOTE:When a generally-used twisted pair Ethernet (TPE) or UTP cable is used, a communication error may occurdepending on your operating environment. In such case, you may be requested to use a shielded twisted paircable.EA2- 1
Page 3 and 4:
TOSHIBA Barcode PrinterB-EX4T1 SERI
Page 10 and 11:
1. PRODUCT OVERVIEW ENGLISH VERSION
Page 12:
1. PRODUCT OVERVIEW ENGLISH VERSION
Page 15 and 16:
2. PRINTER SETUP ENGLISH VERSION EO
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60: 2. PRINTER SETUP ENGLISH VERSION EO
Page 81 and 82: 2.PRINTER SETUPENGLISH VERSION EO1-
Page 83 and 84: 2.PRINTER SETUPENGLISH VERSION EO1-
Page 85 and 86: 3. ON LINE MODE ENGLISH VERSION EO1
Page 91 and 92: 4. MAINTENANCE ENGLISH VERSION EO1-
Page 93 and 94: 5. TROUBLESHOOTING ENGLISH VERSION
Page 99 and 100: 6. PRINTER SPECIFICATIONS ENGLISH V
Page 101 and 102: 7. SUPPLY SPECIFICATIONS ENGLISH VE
Page 109: APPENDIX 1 MESSAGES AND LEDSENGLISH
Page 113 and 114: APPENDIX 2 INTERFACEENGLISH VERSION
Page 115 and 116: APPENDIX 2 INTERFACEENGLISH VERSION
Page 117 and 118: APPENDIX 3 PRINT SAMPLESENGLISH VER
Page 123 and 124: APPENDIX 4 GLOSSARIESENGLISH VERSIO
show all

Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

Create successful ePaper yourself

Delete template?

Save as template?