Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

More documents

Recommendations

Info

2. PRINTER SETUP ENGLISH VERSION EO1-330892.9 Position and Print Tone Fine Adjustment2.9 Position and PrintTone FineAdjustmentThis section describes how to fine adjust a print start position, cut/stripposition, reverse feed amount, print tone, and ribbon motor torque.When a fine adjustment is required, follow the procedure below.Power OFFPower ONONLINE Mode[PAUSE]PAUSE stateHold down [RESTART]Hold down [MODE]User System Mode• Reset• Parameter setting (⇒Section 2.6.2)• Fine adjustment (⇒Section 2.9)• LAN/WLAN (⇒Section 2.6.3)• BASIC (⇒Section 2.6.4)• Z-MODE (⇒Section 2.6.5)• AUTO calibration (⇒Section 2.6.6)• Dump mode (⇒Section 2.6.7)• Log (⇒Section 2.6.8)2.9.1 Fine AdjustmentUSER SYSTEM MODERESETPARAMETER SETADJUST SETLAN/WLANContents of the Fine Adjustment MenuMenuAdjust setParameterFEED ADJ.CUT ADJ.BACK ADJ.X ADJUSTTONE ADJ. (TRANS.)TONE ADJ. (DIRECT)RBN ADJ. RBN ADJ. THRESHOLD THRESHOLD Adjusts the feed amount to theprint start positionAdjusts the cut or strip position.Adjusts the reverse feed amount.Adjusts the print position in Xcoordinate (horizontal direction)Adjusts the print tone for thermaltransfer printing.Adjusts the print tone for directthermal printing.Adjusts the ribbon take-up motordrive voltage.Adjusts the ribbon feed motordrive voltage.Sets a fine adjustment value for thethreshold for the reflective sensor.Sets a fine adjustment value for thethreshold for the transmissivesensor.NOTE:<strong>The</strong> printer driver’s properties screen also has Parameter Fine Adjustmentmenu.E2-60
2. PRINTER SETUP ENGLISH VERSION EO1-330892.9 Position and Print Tone Fine Adjustment2.9.1 Fine Adjustment(Cont.)(1) FEED ADJ.Print start position is shifted by fine adjusting the feed amount.50.0mm49.9mm-49.9mm-50.0mm• Example of Print Start Position Fine AdjustmentWhen setting +3.0 mmCompared with “+0.0mm” position, the print startposition is shifted forward.Feed Direction3mmOne labelPrint Start PositionWhen setting +0.0 mmWhen setting –3.0 mmCompared with “+0.0mm” position, the print startposition is shifted backward.Feed Direction3mmOne labelPrint Start PositionFeed DirectionOne labelPrint Start PositionE2-61
Page 3 and 4:
TOSHIBA Barcode PrinterB-EX4T1 SERI
Page 10 and 11:
1. PRODUCT OVERVIEW ENGLISH VERSION
Page 12:
1. PRODUCT OVERVIEW ENGLISH VERSION
Page 15 and 16:
2. PRINTER SETUP ENGLISH VERSION EO
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24: 2. PRINTER SETUP ENGLISH VERSION EO
Page 73: 2. PRINTER SETUP ENGLISH VERSION EO
Page 81 and 82: 2.PRINTER SETUPENGLISH VERSION EO1-
Page 83 and 84: 2.PRINTER SETUPENGLISH VERSION EO1-
Page 85 and 86: 3. ON LINE MODE ENGLISH VERSION EO1
Page 91 and 92: 4. MAINTENANCE ENGLISH VERSION EO1-
Page 93 and 94: 5. TROUBLESHOOTING ENGLISH VERSION
Page 99 and 100: 6. PRINTER SPECIFICATIONS ENGLISH V
Page 101 and 102: 7. SUPPLY SPECIFICATIONS ENGLISH VE
Page 109 and 110: APPENDIX 1 MESSAGES AND LEDSENGLISH
Page 111 and 112: APPENDIX 2 INTERFACEENGLISH VERSION
Page 117 and 118: APPENDIX 3 PRINT SAMPLESENGLISH VER
Page 123 and 124: APPENDIX 4 GLOSSARIESENGLISH VERSIO
show all

Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

Create successful ePaper yourself

Delete template?

Save as template?