Merlins Ralliart and EvoX TUNING GUIDE Version K.pdf - EvoScan

More documents

Recommendations

Info

MERLINS RALLIART & EVOLUTION-X TUNING GUIDE1.9-SETTING THE DEFAULT COLOUR MAPTo set or change the COLOUR MAP style, select:File \ OptionsThen click on:Default Color Map to get the window shown below.Scroll through the selections and select whatever suites, as some colour stylesdisplay better than others or allow easier data viewing. Some of the more readablestyles with good graduation are:BLUORNG, COLDFIRE, FIRESTRM, JFAN, PALE, RAINBOW, VULCANO, SUNSHINE.FIRESTRM, for example is very good for fuel maps.Click on:Apply then close the window.Figure 5:EcuFLASH – DEFAULT COLOUR MAP STYLEThe colour maps can be tweaked to your own tastes. Open the .MAP file to beedited with NOTEPAD. The data is organized in columns, by the three primarycolours: red, yellow, blue. The higher the number the percentage that colour.REV: 0.K merlin@three.com.au Page 18 of 134
MERLINS RALLIART & EVOLUTION-X TUNING GUIDE1.10-CONNECTING to the ECUFirst, a caution: It has been reported that cables fitted with a connection to pin 9can, on very rare occasions, brick the ETACS unit. Pin 9 is a timing pulse signalrequired for flashing Subaru ECUs and is not required for flashing the Evo EFIcontroller. If your cable has this pin fitted, the safe move is to remove it with a pairof long-nose pliers.Ok, you have your OBD-II cable, and have EcuFLASH up-and-running on yourlaptop. Take a quick look at the photo of the relevant connector. Proceed to the Evoand connect the OBD-II cable to the black OBD-II port. The connector is behind thedash facia, drivers side, adjacent to the centre tunnel. Just feel with your hand andplug the connector into the receptacle. Pix from Biggles on MLR.Figure 6:OBD-II PORTPlug the USB end of the cable into your laptop, it seems to be a good practice toalways use the same port to prevent USB driver conflicts. At least this was aproblem when mixing 1.3U cables and OpenPort2 cables.The cable will talk to the laptop and proceed to install itself. Just follow the promptsand select Proceed Anyway when questioned about proceeding.When the cable is installed and all is ready, the READ ECU icon will light-up with ablue arrow. Important note, make sure the car battery is charged or theread/write operation may fail. A failed write is bad news!REV: 0.K merlin@three.com.au Page 19 of 134
Page 1: MERLINS RALLIART & EVOLUTION-X TUNI
Page 13 and 14: MERLINS RALLIART & EVOLUTION-X TUNI
Page 69 and 70:
MERLINS RALLIART & EVOLUTION-X TUNI
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
P0444P0445P0446P0447P0448P0449P0450
Page 131 and 132:
Page 133 and 134:
P0823P0824P0825P0830P0831P0832P0833
show all

Merlins Ralliart and EvoX TUNING GUIDE Version K.pdf - EvoScan

Create successful ePaper yourself

Delete template?

Save as template?