Range Rover Workshop Manual - Eng - Landiesrus

More documents

Recommendations

Info

12ENGINE NEW RANGE ROVER62. With assistance position engine in engine bay,align to gearbox and locate on dowels.63. Fit crash bracket to gearbox flange and fit andtighten engine to gearbox bolts to 45 Nm (33lbf.ft).64. Lower and remove support from gearbox.65. Fit breather hoses to clip on engine RH liftingeye.66. Position earth strap to RH cylinder head andsecure with bolt.67. Fit engine mountings, lower engine ontomountings and tighten nuts to 45 Nm (33 lbf.ft).68. Lower lifting equipment and remove from engine.69. Align torque converter and drive plate. Fit boltsand tighten to 50 Nm (37 lbf.ft).70. Fit access plug.71. Ensure mating face of exhaust front pipe ,intermediate pipe and exhaust manifolds areclean.72. Use new gaskets, fit front pipe to exhaustmanifolds and tighten nuts to 30 Nm (22 lbf.ft).73. Fit intermediate pipe to front pipe, align clampand tighten nuts to 25 Nm (18 lbf.ft).74. Secure purge pipe to rear engine lift eye withcable tie.75. Fit bolt to secure harness ’P’ clip to LH cylinderhead.76. Connect harness to alternator and tighten B +terminal nut to 18 Nm (13 lbf.ft) and D +terminal nut to 5 Nm (3.5 lbf.ft).77. Connect multiplug to CKP sensor.78. Connect multiplugs to fuel injectors and ECTsensor.79. Fit harness clips to fuel rail and heater coolantpipe.80. Connect multiplug to Canister Vent Solenoid(CVS) unit.81. Connect engine harness multiplug to mainharness.82. Connect earth leads to stud on RH wing valanceand tighten nut to 10 Nm (7 lbf.ft).83. Connect engine harness multiplug to fuse box.84. Secure harness clip to RH wing valance.85. Fit bolts to secure fuse box.86. Fit harness clamp to battery carrier and securewith screws.87. Fit battery positive lead to battery carrier andconnect cable to battery terminal. Connect fusebox positive feed to terminal clamp bolt andsecure with nut. Fit terminal cover.88. Fit engine earth lead to alternator bracket andtighten bolt to 20 Nm (15 lbf.ft).89. Secure harness to coolant rail.90. Connect Lucar to oil pressure switch.91. Connect multiplug to CMP sensor.92. Connect battery lead to starter solenoid andtighten nut to 18 Nm (13 lbf.ft).93. Connect Lucar to starter solenoid.94. Connect multiplug to RH KS and secure harnessclip to engine RH mounting bracket.95. Connect multiplug to LH KS, align harness ’P’clip to cylinder block and tighten bolt to 20 Nm(15 lbf.ft).96. Align gearbox oil cooler pipes, fit spacer andclamp and tighten bolt to 18 Nm (13 lbf.ft).97. Ensure engine oil cooler pipe unions are clean.Fit new ’O’ rings, connect pipes to oil pump andtighten unions to 15 Nm (11 lbf.ft).98. Align engine oil cooler return pipe to alternatormounting bracket and secure with bolt.99. Align EVAP pipe and connect multiplug to purgevalve.100. Connect and secure heater hoses to coolantrails.101. Fit thermostat housing and hose assembly.Connect and secure hoses to coolant rails.102. Connect and secure coolant hose to waterpump.103. Ensure PAS pump and mating face is clean . FitPAS pump to mounting bracket and tighten boltsto 22 Nm (16 lbf.ft).104. Ensure compressor and mating face is clean. Fitcompressor to mounting bracket and tightenbolts to 22 Nm (16 lbf.ft).105. Connect multiplug to compressor.106. Ensure auxiliary drive belt pulley grooves areclean and free from damage.107. Fit new drive belt to pulleys, and ensure belt iscorrectly aligned in pulley grooves.108. With assistance, hold tensioner fully clockwiseand fit drive belt to remaining pulley.109. Fit auxiliary drive belt cover and spacers andtighten bolts to 18 Nm (13 lbf.ft).110. Connect and secure coolant top hose to adaptoron inlet manifold.111. Connect multiplug to MAF sensor.112. Ensure connection is clean and connect fuelpipe to fuel rail.113. Fit ignition coils. See FUEL SYSTEM, Repair.114. Fit radiator. See COOLING SYSTEM, Repair.115. Fit engine oil filter and fill engine with engine oil.See LUBRICANTS, FLUIDS ANDCAPACITIES, Information.116. Check and if necessary top up gearbox oil.24 REPAIR
LAND ROVER V8FLYWHEELService repair no - 12.53.07Remove1. Remove clutch assembly. See CLUTCH,Repair.2. Rotate flywheel until location dowel is oppositestarter motor.3. Remove 6 flywheel securing bolts. Removeflywheel.Refit6. Ensure mating surfaces, dowel and dowellocations in both flywheel and crankshaft areclean.7. Offer flywheel up to crankshaft. Locate on dowel.8. Refit flywheel bolts. Tighten to 80 Nm (59 lbf.ft)9. Refit clutch assembly. See CLUTCH, Repair.4. Inspect flywheel clutch face for cracks, scores oroverheating.5. Inspect ring gear for worn, chipped or brokenteeth.REPAIR25
Page 2 and 3: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 4 and 5: 12ENGINE NEW RANGE ROVERDRIVE PLATE
Page 6 and 7: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 8 and 9: 12ENGINE NEW RANGE ROVER23. Remove
Page 10 and 11: 12ENGINE NEW RANGE ROVER46. Release
Page 12 and 13: 12ENGINE NEW RANGE ROVER75. Manual
Page 14 and 15: 12ENGINE NEW RANGE ROVER88. Attach
Page 16 and 17: 12ENGINE NEW RANGE ROVER161. Fit EC
Page 18 and 19: 12ENGINE NEW RANGE ROVER14. Release
Page 26 and 27: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 32 and 33: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 34 and 35: 12ENGINE NEW RANGE ROVER8. Connect
Page 36 and 37: 12ENGINE NEW RANGE ROVERRefitREAR E
Page 38 and 39: 12ENGINE NEW RANGE ROVEROIL FILTERO
Page 40 and 41: 12ENGINE NEW RANGE ROVEROIL PRESSUR
Page 42 and 43: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 44 and 45: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 46 and 47: 12ENGINE NEW RANGE ROVERROCKER SHAF
Page 48 and 49: 12ENGINE NEW RANGE ROVER14. Positio
Page 50 and 51: 12ENGINE NEW RANGE ROVERTAPPETS - E
Page 52 and 53: 12ENGINE NEW RANGE ROVER5. Progress
Page 54 and 55: 12ENGINE NEW RANGE ROVER4. Remove b
Page 56: 12ENGINE NEW RANGE ROVERRefit7. Cle

Range Rover Workshop Manual - Eng - Landiesrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?