Range Rover Workshop Manual - Eng - Landiesrus

More documents

Recommendations

Info

12ENGINE NEW RANGE ROVER12. Remove engine oil filter.13. Disconnect Lucar from oil pressure switch.14. Disconnect multiplug from CMP sensor.10. Position cloth to collect spillage and loosen bothgearbox fluid cooler pipe unions and engine oilcooler inlet pipe union.15. Remove bolt securing engine oil cooler returnpipe to alternator bracket.11. Remove 2 clips securing radiator cowl andremove cowl.30 REPAIR
LAND ROVER V816. Loosen unions and disconnect oil cooler feedand return pipes from front cover , remove anddiscard ’O’ rings.CAUTION: Plug the connections.17. Remove 9 bolts securing front gear cover andremove cover. Remove and discard gasket.Refit21. Fit new ’O’ rings to oil cooler pipes, connectpipes to front cover and tighten unions to 15 Nm(11 lbf.ft).22. Fit bolt securing oil cooler return pipe toalternator mounting bracket.23. Connect Lucar to oil pressure switch.24. Connect multiplug to CMP sensor.25. Ensure oil filter seal and mating face on frontcover is clean.26. Lubricate seal with clean engine oil and fitengine oil filter.27. Fit radiator cowl and secure with clips.28. Fit oil cooler pipes into recesses in radiator cowland tighten pipe unions to 30 Nm (22 lbf.ft).29. Fit thermostat housing to radiator cowl.30. Connect bottom coolant hose to radiator andsecure with clip.31. Connect hose to water pump and secure withclip.32. Connect top hose to radiator and secure withclip.33. Ensure mating faces of water pump pulley anddrive flange are clean, fit pulley and tighten boltsto 22 Nm (16 lbf.ft).34. Fit auxiliary belt jockey pulley and tighten bolt to50 Nm (37 lbf.ft).35. Fit front cover oil seal. See this section.36. Fit oil pick-up strainer. See this section.37. Refill cooling system. See COOLING SYSTEM,Repair.18. Clean mating faces of front cover and cylinderblock. Clean dowels and dowel holes.19. Fit new gasket onto dowels in cylinder block.20. Fit front cover to cylinder block and tighten boltsin sequence shown to 22 Nm (16 lbf.ft). EnsureCMP sensor multiplug bracket is secured by bolt.REPAIR31
Page 2 and 3: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 4 and 5: 12ENGINE NEW RANGE ROVERDRIVE PLATE
Page 6 and 7: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 8 and 9: 12ENGINE NEW RANGE ROVER23. Remove
Page 10 and 11: 12ENGINE NEW RANGE ROVER46. Release
Page 12 and 13: 12ENGINE NEW RANGE ROVER75. Manual
Page 14 and 15: 12ENGINE NEW RANGE ROVER88. Attach
Page 16 and 17: 12ENGINE NEW RANGE ROVER161. Fit EC
Page 18 and 19: 12ENGINE NEW RANGE ROVER14. Release
Page 24 and 25: 12ENGINE NEW RANGE ROVER62. With as
Page 26 and 27: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 32 and 33: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 34 and 35: 12ENGINE NEW RANGE ROVER8. Connect
Page 36 and 37: 12ENGINE NEW RANGE ROVERRefitREAR E
Page 38 and 39: 12ENGINE NEW RANGE ROVEROIL FILTERO
Page 40 and 41: 12ENGINE NEW RANGE ROVEROIL PRESSUR
Page 42 and 43: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 44 and 45: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 46 and 47: 12ENGINE NEW RANGE ROVERROCKER SHAF
Page 48 and 49: 12ENGINE NEW RANGE ROVER14. Positio
Page 50 and 51: 12ENGINE NEW RANGE ROVERTAPPETS - E
Page 52 and 53: 12ENGINE NEW RANGE ROVER5. Progress
Page 54 and 55: 12ENGINE NEW RANGE ROVER4. Remove b
Page 56: 12ENGINE NEW RANGE ROVERRefit7. Cle

Range Rover Workshop Manual - Eng - Landiesrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?