Range Rover Workshop Manual - Eng - Landiesrus

More documents

Recommendations

Info

12ENGINE NEW RANGE ROVERROCKER SHAFT - OVERHAULService repair no - 12.29.49 - LH ShaftService repair no - 12.29.50 - RH ShaftService repair no - 12.29.55 - Both ShaftsRemove4. Remove rocker shaft assembly. Ensurepushrods remain seated in tappets.Do not carry out further dismantling ifcomponent is removed for access only.5. Remove and discard split pin from one end ofrocker shaft.1. Disconnect battery negative lead.2. Remove relevant rocker cover. See thissection.NOTE: If both shafts are to be removed,identify each assembly to ensure refitmenton original cylinder bank.3. Remove 4 bolts securing rocker shaft assembly.6. Remove the following components:NOTE: Retain components in correctsequence for re-assembly.7. Plain washer.8. Wave washer.9. Rocker arms.10. Rocker pillars.11. Springs.12. Clean all components.13. Inspect all components for wear.14. Inspect rocker shaft and bores in rocker arms. Ifexcessively worn or scored, fit new components.15. Replace all weak or broken springs.16. Lubricate all moving parts with clean engine oil.17. Re-assemble rocker shafts. Ensure thatcomponents are returned to their originalpositions, use new split pins to retaincomponents.18. Ensure shaft identification groove is positionedat one o’clock, with pushrod locations of rockerarms to the right.CAUTION: Oil feed restriction will result ifrocker shafts are incorrectly assembled.46 REPAIR
LAND ROVER V8Refit19. Refit rocker shaft to original cylinder bank.20. <strong>Eng</strong>age push-rods in rocker arm locations.21. Refit rocker shaft securing bolts. Tighten workingfrom centre outwards to 38 Nm (28 lbf.ft).22. Refit rocker cover. See this section.23. Reconnect battery negative lead.SUMP - up to 99MYService repair no - 12.60.44Remove1. Disconnect battery earth lead.2. Raise vehicle on 4 post ramp.3. Remove engine acoustic cover (if applicable).See CHASSIS AND BODY, Repair.4. Remove gearbox acoustic cover (if applicable).See CHASSIS AND BODY, Repair.5. Remove engine oil dip stick.6. Drain engine oil from sump. Refit sump plug.7. Position support under chassis frontcrossmember.8. Lower ramp to give clearance between front axleand sump.REPAIR47
Page 2 and 3: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 4 and 5: 12ENGINE NEW RANGE ROVERDRIVE PLATE
Page 6 and 7: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 8 and 9: 12ENGINE NEW RANGE ROVER23. Remove
Page 10 and 11: 12ENGINE NEW RANGE ROVER46. Release
Page 12 and 13: 12ENGINE NEW RANGE ROVER75. Manual
Page 14 and 15: 12ENGINE NEW RANGE ROVER88. Attach
Page 16 and 17: 12ENGINE NEW RANGE ROVER161. Fit EC
Page 18 and 19: 12ENGINE NEW RANGE ROVER14. Release
Page 24 and 25: 12ENGINE NEW RANGE ROVER62. With as
Page 26 and 27: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 32 and 33: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 34 and 35: 12ENGINE NEW RANGE ROVER8. Connect
Page 36 and 37: 12ENGINE NEW RANGE ROVERRefitREAR E
Page 38 and 39: 12ENGINE NEW RANGE ROVEROIL FILTERO
Page 40 and 41: 12ENGINE NEW RANGE ROVEROIL PRESSUR
Page 42 and 43: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 44 and 45: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 48 and 49: 12ENGINE NEW RANGE ROVER14. Positio
Page 50 and 51: 12ENGINE NEW RANGE ROVERTAPPETS - E
Page 52 and 53: 12ENGINE NEW RANGE ROVER5. Progress
Page 54 and 55: 12ENGINE NEW RANGE ROVER4. Remove b
Page 56: 12ENGINE NEW RANGE ROVERRefit7. Cle

Range Rover Workshop Manual - Eng - Landiesrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?