Range Rover Workshop Manual - Eng - Landiesrus

More documents

Recommendations

Info

12ENGINE NEW RANGE ROVER5. Progressively remove 4 bolts securing rockershaft and remove rocker shaft.6. Remove push rods.NOTE: Store push rods in their fittedorder.9. Remove cylinder head gasket.Refit10. Clean mating faces of cylinder block and headusing suitable gasket removal spray and aplastic scraper, ensure that bolt holes in blockare clean and dry.CAUTION: Do not use metal scraper ormachined surfaces may be damaged.11. Check head and block faces for warping andpitting.12. Fit cylinder head gasket with the word TOPuppermost.NOTE: Gasket must be fitted dry.7. In the sequence shown remove 10 boltssecuring the cylinder head to block.8. Remove cylinder head.13. Carefully fit cylinder head and locate on dowels.14. Lightly lubricate new cylinder head bolt threadswith clean engine oil.52 REPAIR
LAND ROVER V8NOTE: Long bolts: 1, 3, 5.CYLINDER HEAD GASKET (RH) - from 99MYService repair no - 12.29.03Remove1. Remove inlet manifold gasket. See MANIFOLDAND EXHAUST SYSTEM, Repair.2. Remove RH exhaust manifold gasket. SeeMANIFOLD AND EXHAUST SYSTEM, Repair.NOTE: RHD models: Exhaust manifold willremain captive in engine bay but clear ofcylinder head.15. Fit bolts and tighten in the sequence shown to20 Nm (15 lbf.ft) then 90 ° , then a further 90 ° .16. Clean push rods.17. Lubricate ends of push rods with clean engineoil.18. Fit push rods in their removed order.19. Clean base of rocker pillars and mating faces oncylinder head.20. Clean contact surface on rockers, valves andpush rods.21. Lubricate contact surfaces and rocker shaft withclean engine oil.22. Fit rocker shaft assembly and engage push rods.23. Tighten rocker shaft securing bolts progressivelyto 38 Nm (28 lbf.ft).24. Fit and tighten engine harness bolt to 20 Nm (15lbf.ft).25. Refit rocker cover.26. Ensure dipstick tube and mating face on cylinderblock is clean.27. Apply Loctite 638 to end of dipstick tube and fittube and dipstick to cylinder block.28. Fit exhaust manifold. See MANIFOLD ANDEXHAUST SYSTEM, Repair.29. Fit inlet manifold gasket. See MANIFOLD ANDEXHAUST SYSTEM, Repair.3. Remove bolt securing auxiliary drive belttensioner and remove tensioner.REPAIR53
Page 2 and 3: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 4 and 5: 12ENGINE NEW RANGE ROVERDRIVE PLATE
Page 6 and 7: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 8 and 9: 12ENGINE NEW RANGE ROVER23. Remove
Page 10 and 11: 12ENGINE NEW RANGE ROVER46. Release
Page 12 and 13: 12ENGINE NEW RANGE ROVER75. Manual
Page 14 and 15: 12ENGINE NEW RANGE ROVER88. Attach
Page 16 and 17: 12ENGINE NEW RANGE ROVER161. Fit EC
Page 18 and 19: 12ENGINE NEW RANGE ROVER14. Release
Page 24 and 25: 12ENGINE NEW RANGE ROVER62. With as
Page 26 and 27: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 32 and 33: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 34 and 35: 12ENGINE NEW RANGE ROVER8. Connect
Page 36 and 37: 12ENGINE NEW RANGE ROVERRefitREAR E
Page 38 and 39: 12ENGINE NEW RANGE ROVEROIL FILTERO
Page 40 and 41: 12ENGINE NEW RANGE ROVEROIL PRESSUR
Page 42 and 43: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 44 and 45: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 46 and 47: 12ENGINE NEW RANGE ROVERROCKER SHAF
Page 48 and 49: 12ENGINE NEW RANGE ROVER14. Positio
Page 50 and 51: 12ENGINE NEW RANGE ROVERTAPPETS - E
Page 54 and 55: 12ENGINE NEW RANGE ROVER4. Remove b
Page 56: 12ENGINE NEW RANGE ROVERRefit7. Cle

Range Rover Workshop Manual - Eng - Landiesrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?