Range Rover Workshop Manual - Eng - Landiesrus

More documents

Recommendations

Info

12ENGINE NEW RANGE ROVEROIL PRESSURE SWITCH - up to 99MYService repair no - 12.60.50Remove1. Disconnect battery negative lead.Remove cooling fan. See COOLING SYSTEM,Repair.2. Remove alternator drive belt tensioner. SeeELECTRICAL, Repair.3. Disconnect Lucar from oil pressure switch.4. Remove switch and discard ’O’ ring.OIL PRESSURE SWITCH - from 99MYService repair no - 12.60.50Remove1. Release fixings and remove battery cover.2. Disconnect battery earth lead.3. Raise vehicle on 4 post ramp.4. Remove oil filter. See this section.5. Remove bolt securing engine oil cooler returnpipe to alternator support bracket.Refit5. Ensure switch thread and seating in front coverare clean.6. Lubricate new ’O’ ring with clean engine oil. Fitto switch.7. Fit switch. Tighten to 15 Nm (11 lbf.ft)8. Refit alternator drive belt tensioner. SeeELECTRICAL, Repair.9. Fit cooling fan. See COOLING SYSTEM,Repair.10. Reconnect battery negative lead.6. Loosen union and remove oil cooler return pipe.40 REPAIR
LAND ROVER V8STRAINER - OIL PICK-UPService repair no - 12.60.20Remove1. Remove sump gasket. See this section.7. Disconnect Lucar from oil pressure switch.8. Position container below switch to catch oilspillage.9. Remove oil pressure switch and discard ’O’ ring.Refit10. Clean oil pressure switch threads.11. Fit new ’O’ ring to switch.12. Fit oil pressure switch and tighten to 15 Nm (11lbf.ft).13. Connect Lucar.14. Ensure oil cooler return pipe union is clean andfit new ’O’ ring to pipe.15. Align oil cooler return pipe to alternator supportbracket and fit but do not tighten bolt at thisstage.16. Tighten oil cooler return pipe union to 15 Nm (11lbf.ft).17. Tighten bolt securing oil cooler return pipe toalternator support bracket.18. Fit oil filter. See this section.19. Connect battery earth lead.20. Fit battery cover and secure with fixings.21. Top up engine oil.2. Remove 2 bolts and 1 nut securing oil pick-upstrainer.3. Remove oil pick-up strainer.4. Collect spacer from stud.5. Remove and discard ’O’ring.Refit6. Clean oil pick-up strainer and ’O’ ring recess.7. Lubricate and fit new ’O’ ring.8. Locate spacer on stud.9. Position oil pick-up strainer, fit and tighten, boltsto 10 Nm (7 lbf.ft) and, nut to 22 Nm (17 lbf.ft).10. Fit new sump gasket. See this section.REPAIR41
Page 2 and 3: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 4 and 5: 12ENGINE NEW RANGE ROVERDRIVE PLATE
Page 6 and 7: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 8 and 9: 12ENGINE NEW RANGE ROVER23. Remove
Page 10 and 11: 12ENGINE NEW RANGE ROVER46. Release
Page 12 and 13: 12ENGINE NEW RANGE ROVER75. Manual
Page 14 and 15: 12ENGINE NEW RANGE ROVER88. Attach
Page 16 and 17: 12ENGINE NEW RANGE ROVER161. Fit EC
Page 18 and 19: 12ENGINE NEW RANGE ROVER14. Release
Page 24 and 25: 12ENGINE NEW RANGE ROVER62. With as
Page 26 and 27: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 32 and 33: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 34 and 35: 12ENGINE NEW RANGE ROVER8. Connect
Page 36 and 37: 12ENGINE NEW RANGE ROVERRefitREAR E
Page 38 and 39: 12ENGINE NEW RANGE ROVEROIL FILTERO
Page 42 and 43: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 44 and 45: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 46 and 47: 12ENGINE NEW RANGE ROVERROCKER SHAF
Page 48 and 49: 12ENGINE NEW RANGE ROVER14. Positio
Page 50 and 51: 12ENGINE NEW RANGE ROVERTAPPETS - E
Page 52 and 53: 12ENGINE NEW RANGE ROVER5. Progress
Page 54 and 55: 12ENGINE NEW RANGE ROVER4. Remove b
Page 56: 12ENGINE NEW RANGE ROVERRefit7. Cle

Range Rover Workshop Manual - Eng - Landiesrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?