Range Rover Workshop Manual - Eng - Landiesrus

More documents

Recommendations

Info

12ENGINE NEW RANGE ROVER4. Remove bolt securing engine earth lead.5. Remove bolt securing engine oil cooler pipe toalternator mounting bracket.9. Progressively remove 4 bolts securing the rockershaft and remove rocker shaft assembly.10. Remove push rods.6. Remove 4 bolts securing alternator mountingbracket and remove bracket.NOTE: Store push rods in their fittedorder.7. Disconnect HT leads from spark plugs.8. Remove rocker cover.11. In the sequence shown remove 10 boltssecuring the cylinder head.12. Remove cylinder head.13. Remove cylinder head gasket.54 REPAIR
LAND ROVER V8Refit14. Use a suitable gasket removal spray and plasticscraper to clean cylinder head and cylinder blockmating faces. Ensure bolt holes are left cleanand dry.CAUTION: Do not use metal scraper ormachined surfaces may be damaged.TIMING CHAIN AND GEARS - from 99MYService repair no - 12.65.12Remove1. Remove front cover gasket. See this section.15. Check head and block faces for warping andpitting.16. Fit cylinder head gasket with the word TOPuppermost.NOTE: Gasket must be fitted dry.17. Carefully fit cylinder head and locate on dowels.18. Lightly lubricate new cylinder head bolt threadswith clean engine oil.NOTE: Long bolts: 1, 3, 5. short bolts: 2, 4,6, 7, 8, 9, 10.19. Fit bolts and tighten in the sequence shown to20 Nm (15 lbf.ft) then 90 ° , then a further 90 ° .20. Clean push rods.21. Lubricate ends of push rods with clean engineoil.22. Fit push rods in their removed order.23. Clean base of rocker pillars and mating face oncylinder head.24. Clean contact surface on rockers, valves andpush rods.25. Lubricate contact surface and rocker shaft withclean engine oil.26. Fit rocker shaft assembly and engage push rods.Tighten bolts progressively to 38 Nm (28 lbf.ft).27. Fit rocker cover.28. Position alternator mounting bracket, fit andtighten bolts to 40 Nm (30 lbf.ft).29. Position engine harness, align oil cooler pipeand secure with bolt.30. Position auxiliary drive belt tensioner, fit bolt andtighten to 45 Nm (33 lbf.ft).31. Position engine earth lead, fit bolt and tighten to22 Nm (16 lbf.ft).32. Connect HT leads to spark plugs.33. Fit exhaust manifold gasket. See MANIFOLDAND EXHAUST SYSTEM, Repair.34. Fit inlet manifold gasket. See MANIFOLD ANDEXHAUST SYSTEM, Repair.35. Remove stand(s) and lower vehicle.2. Fit crankshaft pulley bolt and rotate engine toalign timing marks. Remove crankshaft pulleybolt.REPAIR55
Page 2 and 3:
12ENGINE NEW RANGE ROVERRefit10. Cl
Page 4 and 5: 12ENGINE NEW RANGE ROVERDRIVE PLATE
Page 6 and 7: 12ENGINE NEW RANGE ROVERRefit10. Cl
Page 8 and 9: 12ENGINE NEW RANGE ROVER23. Remove
Page 10 and 11: 12ENGINE NEW RANGE ROVER46. Release
Page 12 and 13: 12ENGINE NEW RANGE ROVER75. Manual
Page 14 and 15: 12ENGINE NEW RANGE ROVER88. Attach
Page 16 and 17: 12ENGINE NEW RANGE ROVER161. Fit EC
Page 18 and 19: 12ENGINE NEW RANGE ROVER14. Release
Page 24 and 25: 12ENGINE NEW RANGE ROVER62. With as
Page 26 and 27: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 32 and 33: 12ENGINE NEW RANGE ROVERFRONT COVER
Page 34 and 35: 12ENGINE NEW RANGE ROVER8. Connect
Page 36 and 37: 12ENGINE NEW RANGE ROVERRefitREAR E
Page 38 and 39: 12ENGINE NEW RANGE ROVEROIL FILTERO
Page 40 and 41: 12ENGINE NEW RANGE ROVEROIL PRESSUR
Page 42 and 43: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 44 and 45: 12ENGINE NEW RANGE ROVERROCKER COVE
Page 46 and 47: 12ENGINE NEW RANGE ROVERROCKER SHAF
Page 48 and 49: 12ENGINE NEW RANGE ROVER14. Positio
Page 50 and 51: 12ENGINE NEW RANGE ROVERTAPPETS - E
Page 52 and 53: 12ENGINE NEW RANGE ROVER5. Progress
Page 56: 12ENGINE NEW RANGE ROVERRefit7. Cle
show all

Range Rover Workshop Manual - Eng - Landiesrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?