RBT-001 Module - User Manual v.1.2

More documents

Recommendations

Info

Bluetooth SecurityBluetooth security is part of the Generic Access Profile GAP. It is controlled by: Security Modeo Security Mode 1: No Security, the device never will ask for authentication or pairing.o Security Mode 2: The level of security (Authorization, Authentication, Encryption) isdetermined by the setting in the service database entries. Each entrycan have different security requirements. no authentication necessary for SDAP linkso Security Mode 3: Authentication already necessary on Link Manager level: SDAP linksalready require authentication (Service requests) Device always asks for authentication Service Database Entry (only for Security Mode 2)o Each entry can specify the settings for authentication and encryptionThe RBT-001 by default is in Security Mode 2.Get Fixed PINDescriptionReads the current fixed pin code from NVSPacketType REQOpcode GAP_GET_FIXED_PINDataLength 0DescriptionPacketTypeOpcodeDataLengthDataResponse to the request above.CFMGAP_GET_ FIXED _PIN2+PinlengthStatusERROR_OK1 byteERROR_INVALID_NO_OF_PARAMETERSPinlength1 bytePincodePinlength bytesLength of pin code, in bytes.0x00: No Fixed pin, RBT-001 will send "Pin request indicator" incase a pin is required.Range: 0x01-0x10PIN code used when the two Bluetooth devices are paired. Themaximum length of a PIN code is 128 bits (16 bytes).Set Fixed PINDescriptionPacketTypeOpcodeDataLengthDataStores a new fixed pin code in NVSREQGAP_SET_FIXED_PIN1+ PinlengthPinlengthLength of pin code, in bytes.1 byteRange: 0x01-0x10PincodePIN code used when the two Bluetooth devices are paired. ThePinlength bytes maximum length of a PIN code is 128 bits (16 bytes).RoboTech Bluetooth Serial ModuleUser Manual Ver. 1.231
DescriptionResponse to the request above.PacketType CFMOpcode GAP_SET_ FIXED _PINDataLength 1DataStatus1 byteERROR_OKERROR_INVALID_NO_OF_PARAMETERSERROR_PINCODE_LENGTHPIN requestDescriptionThis event is used to inform the Host when a PIN code is requestedduring authentication of an ACL link. This event is only generated if thelength of the Fixed pin parameter stored in the NVS is set to 0.PacketType INDOpcode GAP_GET_PINDataLength 6DataBdAddr6 byteDescriptionPacketType REQOpcode GAP_GET_PINDataLength 1DataLength 7 + PinlengthDataBdAddr6 bytePinlength1 byteDescriptionThe Bluetooth device address of the remote device.This command is used to send a PIN code to the RBT-001 module asresponse to a GAP_GET_PIN indication.PincodePinlength bytesPacketType CFMOpcode GAP_GET _PINDataLength 1DataStatus1 byteGet Security ModeDescriptionResponse to the request above.The Bluetooth device address of the remote device.Length of pin code, in bytes.Range: 0x00-0x100x00 indicates that the Host does not allow the authentication of theACL link.PIN code used when the two Bluetooth devices are paired. Themaximum length of a PIN code is 128 bits (16 bytes).ERROR_OKERROR_INVALID_NO_OF_PARAMETERSERROR_PINCODE_LENGTHReads the current security mode of the Bluetooth device.PacketType REQOpcode GAP_GET_SECURITY_MODEDataLength 0DataNoneRoboTech Bluetooth Serial ModuleUser Manual Ver. 1.232
Page 1: RoboTechBluetooth Serial ModuleRBT-
Page 5 and 6: Release Link.......................
Page 7 and 8: Product DescriptionThe RoboTech Blu
Page 9 and 10: Recommended Operating ConditionsSym
Page 11 and 12: RS232 adapter board schematicRoboTe
Page 13 and 14: Command mode and Transparent modeCo
Page 15 and 16: No. Address Parameter Default Value
Page 17 and 18: Force Master on/offThis flag improv
Page 19 and 20: Idle, Automatic and Idle, Non-autom
Page 21 and 22: Default Connection setup by using "
Page 23 and 24: UART Protocol PrinciplesThe RBT-001
Page 25 and 26: RoboTech Bluetooth Serial ModuleUse
Page 27 and 28: Commands in Command ModeThe RBT-001
Page 29 and 30: Reading the user-friendly name of t
Page 31: Set Scan ModeDescriptionChange the
Page 35 and 36: DescriptionResponse to the request
Page 37 and 38: DescriptionThis command is used to
Page 41 and 42: Serial port profile (SPP)An active
Page 43 and 44: LocalPort1 byteBaudRate1 bytePortse
Page 45 and 46: DescriptionConfirm to the request a
Page 47 and 48: Set Overrun ErrorDescriptionThis co
Page 49 and 50: Establish / Release SPP link to a r
Page 51 and 52: Link ReleasedDescriptionIndicates t
Page 53 and 54: If the link is lost, the RBT-001 wi
Page 55 and 56: DescriptionConfirm to the request a
Page 59 and 60: DescriptionPacketTypeOpcodeDataLeng
Page 61 and 62: DescriptionPacketTypeOpcodeDataLeng
Page 63 and 64: Read Operation ModeDescriptionThis
Page 65 and 66: DescriptionConfirms the request abo
Page 67 and 68: Get Event FilterDescriptionThis com
Page 69 and 70: Each registered service entry itsel
Page 71 and 72: Device ReadyDescriptionPacketTypeOp
Page 73 and 74: Read NVSDescriptionPacketType REQOp
Page 75 and 76: 0x260x270x280x290x2A0x2B0x2C0x2D0x2
Page 77 and 78: Error MacroDescriptioncode0x30 ERRO
Page 79 and 80: CertificationsBluetoothThe RBT-001

RBT-001 Module - User Manual v.1.2

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?