RBT-001 Module - User Manual v.1.2

More documents

Recommendations

Info

DescriptionConfirm to the request above.PacketType CFMOpcode SPP_DELETE_DEFAULT_CONDataLength 1DataIndex1 byteIndex in the default connection storage. Range 0x00 to 0x06.Status1 byte0x00 OKLink supervision TimeoutSet Link TimeoutDescriptionThis command is used to change the current ACL link supervisiontimeout.This command will affect all DLC’s established to the specified device.PacketType REQOpcode SPP_SET_LINK_TIMEOUTDataLength 8DataBdAddr6 bytesThe Bluetooth address of the remote device of the ACL link forwhich the Link Supervision Timeout is changed.LinkTimeout2 byteDescriptionResponse to the request above.The link supervision timeout in slots (0,625ms).0x0000: No link supervision timeout (the timer is disabled)0x0190-0xFFFF: Valid timeout range (in slots)0x7D00: The default value (20s)PacketType CFMOpcode SPP_SET_LINK_TIMEOUTDataLength 7DataStatus1 byteERROR_OKERROR_UNSPECIFIED_ERRORERROR_INVALID_NO_OF_PARAMETERSERROR_NO_CONNECTIONBdAddr6 bytesERROR_ILLEGAL_LINK_TIMEOUTThe Bluetooth address of the remote device of the ACL link forwhich the Link Supervision Timeout is changed.Get Link TimeoutDescriptionThis command is used to get the current link supervision timeoutsetting for the given ACL link.PacketType REQOpcode SPP_GET_LINK_TIMEOUTDataLength 6DataBdAddr6 bytesThe Bluetooth address of the remote device of the ACL link forwhich the Link Supervision Timeout is requested.RoboTech Bluetooth Serial ModuleUser Manual Ver. 1.255
DescriptionResponse to the request above.PacketType CFMOpcode SPP_GET_LINK_TIMEOUTDataLength 9DataStatus1 byteERROR_OKERROR_UNSPECIFIED_ERRORERROR_INVALID_NO_OF_PARAMETERSBdAddr6 bytesLinkTimeout2 byteERROR_NO_CONNECTIONThe Bluetooth address of the remote device of the ACL link forwhich the Link Supervision Timeout is requested.The link supervision timeout in slots (0,625ms).0x0000: No link supervision timeout (the timer is disabled)0x0190-0xFFFF: Valid timeout range (in slots)Service discovery application profile (SDAP)The RBT-001 implements the service discovery application profile (SDAP), and makesservice discovery very simple.A pHostp lic a tio nR E Q , S D A P _ C O N N E C TRBT-001S im p ly(dongle) B lu eC F M , S D A P _ C O N N E C TD o n g le c re a te s a S D Pco n n e c tio nC o n n e ctio n is cre a te d ,s ta rt b ro w s in gR E Q , S D A P _ S E R V IC E _ B R O W S EC F M , S D A P _ S E R V IC E _ B R O W S EP e rfo rm a se a rc h in th ere m o te S D P d a ta b a seH o st re c e iv e s th ere s u lt, n e e d s a d d itio n a lp a ra m e te rsR E Q , S D A P _ S E R V IC E _ S E A R C HC F M , S D A P _ S E R V IC E _ S E A R C HP e rfo rm a s e a rch in th ere m o te S D P d a ta b a s eH o s t h a s fin is h e d th eS D P s e a rc hR E Q , S D A P _ D IS C O N N E C TC F M , S D A P _ D IS C O N N E C TD is c o n n e c t re m o ted e v ic eSDAP Connection HandlingConnectDescriptionCreates an SDP connection to a remote device. Only one SDPconnection can be active.PacketType REQOpcode SDAP_CONNECTDataLength 6DataBdAddr6 bytesThe Bluetooth address of the remote device to connect to.RoboTech Bluetooth Serial ModuleUser Manual Ver. 1.256
Page 1:
RoboTechBluetooth Serial ModuleRBT-
Page 5 and 6: Release Link.......................
Page 7 and 8: Product DescriptionThe RoboTech Blu
Page 9 and 10: Recommended Operating ConditionsSym
Page 11 and 12: RS232 adapter board schematicRoboTe
Page 13 and 14: Command mode and Transparent modeCo
Page 15 and 16: No. Address Parameter Default Value
Page 17 and 18: Force Master on/offThis flag improv
Page 19 and 20: Idle, Automatic and Idle, Non-autom
Page 21 and 22: Default Connection setup by using "
Page 23 and 24: UART Protocol PrinciplesThe RBT-001
Page 25 and 26: RoboTech Bluetooth Serial ModuleUse
Page 27 and 28: Commands in Command ModeThe RBT-001
Page 29 and 30: Reading the user-friendly name of t
Page 31 and 32: Set Scan ModeDescriptionChange the
Page 33 and 34: DescriptionResponse to the request
Page 37 and 38: DescriptionThis command is used to
Page 41 and 42: Serial port profile (SPP)An active
Page 43 and 44: LocalPort1 byteBaudRate1 bytePortse
Page 45 and 46: DescriptionConfirm to the request a
Page 47 and 48: Set Overrun ErrorDescriptionThis co
Page 49 and 50: Establish / Release SPP link to a r
Page 51 and 52: Link ReleasedDescriptionIndicates t
Page 53 and 54: If the link is lost, the RBT-001 wi
Page 55: DescriptionConfirm to the request a
Page 59 and 60: DescriptionPacketTypeOpcodeDataLeng
Page 61 and 62: DescriptionPacketTypeOpcodeDataLeng
Page 63 and 64: Read Operation ModeDescriptionThis
Page 65 and 66: DescriptionConfirms the request abo
Page 67 and 68: Get Event FilterDescriptionThis com
Page 69 and 70: Each registered service entry itsel
Page 71 and 72: Device ReadyDescriptionPacketTypeOp
Page 73 and 74: Read NVSDescriptionPacketType REQOp
Page 75 and 76: 0x260x270x280x290x2A0x2B0x2C0x2D0x2
Page 77 and 78: Error MacroDescriptioncode0x30 ERRO
Page 79 and 80: CertificationsBluetoothThe RBT-001
show all

RBT-001 Module - User Manual v.1.2

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?