RBT-001 Module - User Manual v.1.2

More documents

Recommendations

Info

Technical specificationsPhysical dimensions and pin assignmentPin numberPin nameType(Input/Output)Description1 VCC I Voltage DC input ( Typical 3VDC)2 RX I Serial Port Receive Data (TTL level)3 TX O Serial Port Transmit Data (TTL level)4 RTS O Serial Port Request To Send (active low)5 CTS I Serial Port Clear To Send (active low)6 GND - GroundRoboTech Bluetooth Serial ModuleUser Manual Ver. 1.27
Recommended Operating ConditionsSymbol Parameter Min Typ Max UnitVCC Voltage DC Input 2.5 3.0 3.3 1 VTa Ambient Operating Temperature Range 0 25 45 °C1. Recommended maximum 3.0V for best RF performanceDigital DC CharacteristicsSymbol Parameter Condition Min Max UnitV IH Logical 1 Input Voltage High2.5V ≤ VCC ≤ 3.0V 0.7 x VCC VCC + 0.23.0V ≤ VCC ≤ 3.3V 2.0 VCC + 0.2VV IL Logical 0 Input Voltage Low2.5V ≤ VCC ≤ 3.0V -0.2 0.25 x VCC3.0V ≤ VCC ≤ 3.3V -0.2 0.8VI OH Logical 1 Output CurrentV OH = 2.4V,VCC = 3.0V-10 mAI OL Logical 0 Output CurrentV OL = 0.4V,VCC = 3.0V10 mAPower Supply Requirements 1Symbol Parameter Min Typ 2 Max UnitI RXSL Receive Data in SPP Link, Slave 3 26 mAI RXM Receive Data in SPP Link, Master 3 23 mAI SnM Sniff Mode, Sniff interval 1 second 3 5.6 mAI SC-TLDIS Scanning, No Active Link, TL Disabled 3 0.43 mAI Idle Idle, Scanning Disabled, TL Disabled 3 100 µA1. Based on UART Baudrate 921.6kbit/s.2. VCC = 3.3V, Ambient Temperature = +25 °C.3. Average values excluding LedsTL= Transport LayerRoboTech Bluetooth Serial ModuleUser Manual Ver. 1.28
Page 1: RoboTechBluetooth Serial ModuleRBT-
Page 5 and 6: Release Link.......................
Page 7: Product DescriptionThe RoboTech Blu
Page 11 and 12: RS232 adapter board schematicRoboTe
Page 13 and 14: Command mode and Transparent modeCo
Page 15 and 16: No. Address Parameter Default Value
Page 17 and 18: Force Master on/offThis flag improv
Page 19 and 20: Idle, Automatic and Idle, Non-autom
Page 21 and 22: Default Connection setup by using "
Page 23 and 24: UART Protocol PrinciplesThe RBT-001
Page 25 and 26: RoboTech Bluetooth Serial ModuleUse
Page 27 and 28: Commands in Command ModeThe RBT-001
Page 29 and 30: Reading the user-friendly name of t
Page 31 and 32: Set Scan ModeDescriptionChange the
Page 33 and 34: DescriptionResponse to the request
Page 37 and 38: DescriptionThis command is used to
Page 41 and 42: Serial port profile (SPP)An active
Page 43 and 44: LocalPort1 byteBaudRate1 bytePortse
Page 45 and 46: DescriptionConfirm to the request a
Page 47 and 48: Set Overrun ErrorDescriptionThis co
Page 49 and 50: Establish / Release SPP link to a r
Page 51 and 52: Link ReleasedDescriptionIndicates t
Page 53 and 54: If the link is lost, the RBT-001 wi
Page 55 and 56: DescriptionConfirm to the request a
Page 59 and 60:
DescriptionPacketTypeOpcodeDataLeng
Page 61 and 62:
DescriptionPacketTypeOpcodeDataLeng
Page 63 and 64:
Read Operation ModeDescriptionThis
Page 65 and 66:
DescriptionConfirms the request abo
Page 67 and 68:
Get Event FilterDescriptionThis com
Page 69 and 70:
Each registered service entry itsel
Page 71 and 72:
Device ReadyDescriptionPacketTypeOp
Page 73 and 74:
Read NVSDescriptionPacketType REQOp
Page 75 and 76:
0x260x270x280x290x2A0x2B0x2C0x2D0x2
Page 77 and 78:
Error MacroDescriptioncode0x30 ERRO
Page 79 and 80:
CertificationsBluetoothThe RBT-001
show all

RBT-001 Module - User Manual v.1.2

Create successful ePaper yourself

Delete template?

Save as template?