RENTAL SOLUTIONS GUIDE 2007 - TR Corporation

GENERAL INDUSTRIAL EQUIPMENT
96
induStrial calibratOrS
Fluke 5500A Multi Product Calibrator with NATA Calibrated
FLU,5500A-NATA AU
Calibrator sources direct voltage & current, alternating voltage and current,
with multiple waveforms and harmonics, 2 simultaneous voltage outputs
or voltage & current. Simulates power with phase control, resistance,
capacitance, thermocouples and RTDs. Selectable ranges include the
following outputs Vdc from 0~1.02kV, Vac from 1mV~1.02kV with output from
10Hz~500kHz. AC current from 0.01µA~11A with output from 10Hz~10kHz.
DC current from 0~11A. Resistance values from short circuit to 330MΩ.
Capacitance values from 330pF~1,100µF. Temperature t/c b, C, E, J, K, L,
N, R, S, T, U, RTD pt385 100Ω, pt3926 100Ω, pt3916 100Ω, pt385 200Ω,
pt385 500Ω, pt385 1kΩ, Ni120 120Ω & Cu427 10Ω.
Fluke 725 Process Calibrator
FLU,725 NZ
DC voltage measurement 0.025%, 300V max, source 0.02%, 11V max.
DC current measurement 0.025%, 110mA max, source 0.01%, 22 mA
max. Resistance measurement 0.05%, 11kΩ max, source 0.01%, 11kΩ
max. Frequency measurement 5 counts 1Hz~50kHz, source 1 count
20Hz~5kHz. ‘K’ thermocouple measurement 0.3ºC, source 0.3ºC. pt100
RTD measurement 0.5ºC, source 0.2ºC. Measures and simulates 4~20mA,
t/c E, N, J, K, T, b, R, S, & C, 2, 3 & 4 wire RTDs and frequency. Operates
from drycell batteries.
Fluke 725 Process Calibrator NATA Calibrated
FLU,725-NATA AU
Specification as above but with NATA calibration.
Fluke 743 Calibrator
FLU,743b AU/MY
Includes RS232 interface. DC voltage measurement 0.025%, 300V max,
source 0.01%, 15V max. DC current measurement 0.025%, 110mA max,
source 0.01%, 22mA max. Resistance measurement 0.05%, 11kΩ max,
source 0.01%, 11kΩ max. Frequency measurement 0.5%, +5, 40~500Hz,
source 1 count 20Hz~5kHz. ‘K’ thermocouple measurement 0.3ºC, source
0.3OC pt100. RTDs measurement 0.3ºC, source 0.1ºC. Measures and
simulates 4~20mA, t/c E, N, J, K, T, b, R, S, & C, 2, 3 & 4 wire RTDs,
frequency, test limit switches. Can use scaling factors for measurement &
source. built in calculator. Autostep function. Allows user entered values.
Operates as a 8k point data logger. Note pC software only supports 15
tags.
Fluke 744 DOC Calibrator with Hart
FLU,744 AU/NZ/MY
Documenting process calibrator which includes HART communication
protocols for communicating with and setting up smart transmitters. RS232
interface. DC voltage measurement 0.025%, 300V max, source 0.01%, 15V
max. DC current measurement 0.025%, 110mA max, source 0.01% 22mA
max. Resistance measurement 0.05%, 11kΩ max, source 0.01% 11kΩ max.
Frequency measurement 0.5%, +5, 40~500Hz, source 1 count 20~5kHz. ‘K’
thermocouple measurement 0.3ºC, source 0.3ºC pt100. RTDs measurement
0.3ºC, source 0.1ºC. Measures and simulates 4~20 mA, t/c E, N, J, K, T, b,
R, S & C, 2, 3 & 4 wire RTDs, frequency, test limit switches. Uses scaling
factors for measurement & source. built in calculator. Autostep function.
Allows user entered values. Operates as an 8k point data logger. Note pC
software only supports 15 tags.