RENTAL SOLUTIONS GUIDE 2007 - TR Corporation

Hioki 3128 Clamp-on Current Transducer
HIO,3128 AU
Clamp-on current meter with recorder output. Ranges full scale 15A~1.5kA.
Output 200mV dc full scale. Batteries not required. Output is intended only
for low speed recorders.
Yokogawa 2255-01 10A ~ 5A Current Transformer
YEW,2255-01 AU
Input 10Aac, output 5Aac, max circuit voltage 3.45kV, burden 15VA, accuracy
1% of rated value, bus bar connectors.
Yokogawa 2215 Current Shunt
YEW,2215 AU/MY
50mV output, available in range of 1A~1kA.
Crompton 235/50 Frequency Transducer
CI,253/50 AU
Input 240V ac, 45~55Hz, output 0 ~1mA.
Moore FDT Frequency to Volts Transducer
MOR,FDT AU
Input range 6.5~12.5kHz at up to 20V peak to peak. Output 5Vdc at
12kHz.
Yokogawa 2261-01 2.2kV Potential Transformer
YEW,2261-01 AU
3.3, 2.2kV, 440 & 220V primary to 110V secondary.
Jacobs Radio CT-005 Current Transducer
JR,CT-005 AU
Range 5kA, 2kA & 1kA. 1V dc output. Transformer can be split in two to
accommodate cable or bus 22 x 55mm.
Phase Sequence Meter 110 - 600 volts 50 / 60 Hz
KYO,pSM8031 AU
KYO,8031 MY
phase indicator with open phase checker and phase indicator designed to
check the presence of open phase and also the phase sequence by rotating
disk and lamps. Check a wide range of 3ph power source from 110~600V.
Operational voltage 110~600Vac, time limit for continuous >500V within 5min.
Frequency response 40~200Hz(ac 110~200V), 40~400Hz(ac 200~600V)
safety standard IEC61010-1 CAT.III 600V pollution degree 2 withstand
voltage 2.2kVac for 5s. Dimensions 106L × 75W × 40Dmm, weight 350g
approx. Cord 1.5m(R: red S: white T: blue)
Beha 5774E 3 Phase Sequence/Rotation Indicator
bEH,5774E AU
For determing the rotational direction and sequence of a 3ph supply.
Necessary to pre-determine the correct rotational direction of 3ph motors.
Kikisui PLZ1002W Electronic Load
KIK,pLZ1002W AU/MY
Voltage range 3~110V. Current range 0~200A. In-built oscillator provides
for dynamic load testing by switching between two different load levels.
Load current may be remotely controlled by voltage or resistance signals.
Multiple units may be operated in parallel. In-built digital volt/current meter.
For dc inputs only.
AUSTRALIA
1800 632 652
www.techrentals.com.au
NEW ZEALAND
0800 832 473
www.techrentals.co.nz
electrical tranSducerS
Universal Technic P75.3C dc/ac Amp Clamp
UNI,p75-3C AU
Max current 7,500A dc & ac peak. bandwidth 1KHz. Min range 1kA.
Accuracy at 75A 10% of reading. FS accuracy 2% of reading. Max bus size
122 x 54mm or 100 x 64mm. Max cable size 83mm. battery 9V - life 100h.
Output sockets 4mm. DC current gives dc output, ac current gives ac output,
4kA range 0.5mV per amp, 7.5kA range 0.2mV per A.
Robinson 543 Linear ac Current Transducers
ROb,543 AU
Wide bandwidth and very wide dynamic range. Supplied with an open
ended flexible coil of 3m length which may be wrapped around a very large
conductor or power pole, etc. Frequency range 10Hz~10kHz with 1%
accuracy. Current range for 1 wrap of coil 1A~2MA at 50Hz. phase error
< 0.04deg. Min bending radius 60mm. External insulation is required for
metallic conductor. Output voltage 2V rms ac waveform. Also dc rectified
output. In-built digital display.
LEM FLEXII 30, 300 & 3,000A Transducer
LEM,LEM-FLExII AU
Flexible wrap-around ac current transducer. Length 600mm. Ranges 30,
300A & 3kA. Frequency response 1~20kHz. Accuracy 1%. phase error
0.5O. Output 3Vrms @ full scale. Requires 3 units for 3ph. Designed for
multimeters and oscilloscopes (4mm banana plug or bNC connectors) but can
also be used with the DRA,808 (requires adaptor lead), or VOL,pM3000A.
Other instruments may be attached providing the correct adaptor/transducer
and connection is available. Operates for 100h from 2 x 9V batteries.
electrical teSterS
Biddle 550005 Turns Ratio Test Set
bID,550005 AU
Single phase (can be used on 3ph individual phase windings). Turns ratio
0.001~129.999. Exciting current 0~1A. Accuracy 0.1%. Hand cranked
operation.
AVO Penta-Plus DMM Analyser
AVO,pENTA-pLUS-DMM AU
Multifunction meter for measuring 1 & 3ph volts ac, primary and secondary
current, true and reactive power, amplitude and phase angle, and also
frequency. Easily configured to measure the amplitude and phase angle
between any 2 current or voltage inputs. Displayed simultaneously on a
backlight graphic LCD screen. Internal memory records up to 60 test results.
Logging via RS232C port. parallel printer port. Voltage 0~650Vac, 9 ranges
with 0.1% resolution. Max 1kV. Current 0~100A ac in 11 ranges, with 0.1%
resolution. phase angle 0~360O with 0.1O resolution. power true and
reactive ±0-100kW & ±0~100kVAr. Frequency 45~65Hz. Timer 0~999.999.
Line or battery operated, 3h continuous on full charge.
Metrix MX120 Multicore Clamp-on Meter
MET,Mx120 AU
Measures current in 1, 2, or 3 wire cables. No need to split cables or remove
covers. Ranges 2 or 3 wire 0~40A, 1 wire 0~199.9A resolution 0.1A.
Accuracy 5% with 2 or 3 wire oval or flat cable, 12% with round cable, 1.5%
with single wire. battery operated. Display 3½ digit.
Hioki 3282 Clamp-on Hi Tester (V, I, Hz & T)
HIO,3282 AU
Measures True rms, peak, min/max & hold. Ranges auto/manual, current
30A, 300A & 1kA rms. Voltage 300/600V (1kVmax). Resistance 1/10kΩ.
Frequency 40~100Hz & 66Hz~1kHz. Jaw capacity 46mmØ (50mm opening).
Battery life approx 1.5h continuous.
ELECTRICAL POWER
MALAYSIA
603 5632 1135
www.techrentals.com.my 63