RENTAL SOLUTIONS GUIDE 2007 - TR Corporation

NEW
Omicron CPC 100 PTS for CTs/VTs/Power Transformer
OMI,CpC100pTS AU
Allows for automated testing of power transformers, CTs, VTs, resistance
testing, and more. providing up to 800A (or 2000A with current booster) and
2000V and comes complete with an integrated PC. Its software routines test a
wide range of substation equipment, and automatically creates customizable
reports. Weight: 29 kg. Analog voltages and currents can be measured with
very high precision. Its Ohm meters automatically switch ranges from µOhm
to kOhm to allow for a wide variety of applications. Testing of unconventional
equipment, such as Rogowski Coils or current sensors completes the
spectrum. Safety features: emergency shut off button, safety key lock (block
unauthorised use).
Omicron CMC156-3 Advanced Protection Relay Test Set
OMI,CMC156-3 AU
For three-phase testing of relays, meters and transducers, for applications
requiring portability. • 3 x 125V outputs, • 3 x 12.5A outputs, • 6 x low level
outputs (rear side), • 2 x counter inputs (rear side), • 4 x binary outputs, •
dc measuring inputs, • 10 x binary inputs. Applications are digital distance
relay testing or testing of transformer operated energy. Signal generation
is performed digitally. The 16-bit D/A conversion results in a high quality
signal event at small signal amplitudes. In addition to the 6 outputs of the
amplifier section, 6 independent channels with low-level signals are available
at the back of the unit which can be used to control external amplifiers for
applications requiring more than 3 voltage or current phases, e.g., testing
of differential relays, or applications requiring higher currents or voltages.
They are also useful where there is a need for output power higher than that
provided by the CMC 156. Comes with Test Universe 2.01 software loaded
on dedicated laptop. Weighs 9.8 kg.
Omicron CMC256-6 EP Advanced 3Ph Protection Relay Test
System
OMI,CMC256-6 Ep AU
Current integral 3ph current source max 140VA, 6 output sources, resolution
500µA, suitable for most relay types, including some high burden units.
Voltage 3 ph voltage 0~300rms. Auxiliary dc supply, 0~264V, 0.2A. Relay
monitoring trip, monitoring 6 isolated inputs, can be configured to be voltage
free or 0~250V. Contact outputs 6 isolated change-over relay contacts
(software controlled). Max 250V ac 10A or 125V dc 1A. Interface connector,
16 TTL digital inputs and outputs. Scope analogue inputs, 2 isolated
analogue inputs ±500V peak max 12 bit resolution. Input supply 90~260V
dc, 400Hz. Intuitive on-line help. Notebook 486 or better Win 3.11, 95, 98 or
NT, display SVGA or better. Interface parallel port.
AUSTRALIA
1800 632 652
www.techrentals.com.au
NEW ZEALAND
0800 832 473
www.techrentals.co.nz
prOtectiOn relay teSting SyStemS
Omicron CMGPS Syncronisation Control Unit
OMI,CMGpS AU
GpS-based synchronisation unit, which is used to synchronise CMC
(protection Relay) test sets. Used when performing end-to-end tests of
line protection schemes, the unit provides a start signal pulse based on the
GpS clock time base. Software is both integrated in the testing modules
(State Sequencer) and can also be used as a stand-alone application. Two
independent timing pulses are available via separate connectors, on a 16pin
plug (pulse out 1) which is connected with the CMC test set (external
interface) and on 2 x 4mm banana plugs (pulse out 2). Supplied with GpS
antenna, 15m antenna ext cable, plug-in power supply, CMC-CMGpS
interface cable, users manual, fabric carry bag and a travel case. Weighs
5kgs.
Omicron C-Probe-1 Clamp-on CT ac/dc
OMI,C-pRObE1 AU
An active ac & dc current probe with voltage output. Recommended
accessory for measuring currents with the CMC 256. Two measuring ranges:
10A & 80A. Frequency range dc 10kHz. Accuracy error < 2% for currents up
to 40A and frequencies up to 1kHz. phase error < 0.5O @ 50/60Hz. Length
230mm.
Omicron CMC256-6 Advanced Protection Relay Test Set
OMI,CMC256-6 AU
Advanced 3ph dynamic automatic protection relay test system. Current,
integral 3ph current source max 140VA, 6 output sources, resolution 500µA,
suitable for most relay types, including some high burden units. Voltage,
3ph 0~300rms. Auxiliary dc supply, 0~264V, 0.2A. Relay monitoring trip,
monitoring 6 isolated inputs, can be configured to be voltage free or 0~250V.
Contact outputs 6 isolated change-over relay contacts (software controlled).
Max 250Vac, 10A or 125Vdc 1A. Interface connector, 16 TTL digital inputs
and outputs. Scope analogue inputs, 2 isolated analogue inputs ±500V
peak max 12 bit resolution. Input supply 90~260Vdc, 400Hz. Intuitive online
help. Laptop and Test-Universe software up to TU V 2.01 supplied with
test set, interface parallel port.
Programma Sverker 760 Relay Test Set
pRO,SVERKER760 AU
Relay test set for 1ph protective relay equipment. Three phase relays can
be tested 1 phase at a time or by synchronising more than one unit. Current
ranges to 100A with full load current to 250A. AC outputs to 250V & dc
outputs to 300V. In-built capacitor and resistors for current output phase
shifting (360 0 ). In-built timer, ammeter, and voltmeter. Measures phase
angle, PF, and impedance. RS232 communications and control interface.
ELECTRICAL POWER
MALAYSIA
603 5632 1135
www.techrentals.com.my 57