RENTAL SOLUTIONS GUIDE 2007 - TR Corporation

ELECTRICAL POWER
42
inSulatiOn/cOnditiOn/reSiStance teSterS
> NEW Megger MIT1020 Diagnostic 10kV Insulation
Resistance Tester
MEG,MIT1020-10KV DIT AU
backlit display, variable test voltage from 50~5000V, Automatic IR, pI, DAR,
SV and DD tests, measures to 35TΩ, RS232 & USb download of results.
IEEE 43-2000 recommends the use of 10kV for motor windings rated above
12kV. protection rating of Ip54. Mains or battery powered.
Megger 10-01 10kV Insulation Tester, Test Voltage 500~10,000V
MEG,10-01-10KV AU
The Megger MEG,10-01-10kV Insulation Tester is a compact, Microprocessor
controlled high voltage dc Insulation tester.
> NEW HV Diagnostics 30kV-15mA DC/VLF High Voltage
Insulation DielectricsTest Set
HVD,HVA30-DC/VLF AU/NZ
VLF (0.1Hz), DC (±), cable fault conditioning (burning), and sheath/jacket
testing modes all included. 0.1Hz & 0.02Hz. For solid dielectric cables
such as xLpE and EpR. Fully automatic or manual cable test sequences
complying with International Standards/Guides such as IEEE 400.2, VDE
0296, CENELEC, etc. True symmetrical sinusoidal, load independent,
output waveform across the full load range. Real-time display of actual
output waveform. Easy to use, menu guided, large backlit user interface.
Large output load capability (up to 5µF). Automatic and integrated load
capacitance measurement with optimum frequency selection. Storage of test
results for later retrieval or download to laptop. Short circuited protected.
> NEW HV Diagnostics 60kV-50mA DC/VLF High Voltage
Insulation Dielectrics Test Set
HVD,HVA60-DC/VLF AU
True sine wave low frequency output. 0.1Hz & 0.02HZ. For VLF, DC and
jacket/sheath testing. Fault conditioning capability. Test result storage
capability. Short circuit protection. Complies with CENELEC, IEEE 400.2,
VDE 0296 and other international standards. Manual or fully automatic test
sequence selection. Real-time display of actual output waveform. High
voltage power source suitable for testing electrical plant including cables:
xLpE, pE, EpR, pILC etc, capacitors, switchgear, transformers, rotating
machines, insulators and bushings.
Hioki 3455 High Voltage Insulation Tester
HIO,3455HVIT-5KV AU
pI and DAR function to check insulation quality and step voltage test to detect
for signs of deterioration. Generates a wide range of test voltages, from
250V to 5kV. The voltage may be chosen from the commonly used presets
of 250V, 500V, 1kV, 2.5kV & 5kV, or set to desired level by increments or
decrements of 25V or 100V. Insulation diagnoses for automatic calculation
and indication of pI (polarisation index) and DAR (Dielectric absorption ratio),
step voltage testing and temperature correction. Large memory stores up to
100 manual records and a logging function for 10 data (360 times). Stored
data may be displayed on the LCD or down-loaded to a pC. The date and
time of measurement also recorded.
CHK LM05 Micro-Ohm Meter 10A
CHK,LM05 AU/MY
Operates from internal batteries or external power supply. Max test current
10A. Resistance range up to 20Ω with a max sensitivity of 1µΩ. Includes
power supply-charger, duplex helical test leads, length 2m.
Megger DLRO10 Micro-Ohm Meter
MEG,DLRO10 AU
Self contained automatic micro-ohm meter, selecting the most suitable test
current, up to 10A dc to measure resistance from 0.1mΩ~2kΩ on one of
seven ranges. Instrument is built into a strong, lightweight case that is
equally at home in the field or in the laboratory. Light enough to be worn
around the neck, small enough to be taken into areas which were previously
too small to access. DLRO10 uses a large, bright 4½ digit LED display.
Resolution: 0.1µΩ. battery: rechargeable NiMH, typical life 1,000 test at
full load.