RENTAL SOLUTIONS GUIDE 2007 - TR Corporation

DATA, NETWORK & TELECOMMUNICATIONS
32
lan cable teSterS
Fluke DTX1200 Category 6 Cable Certification Tester
FLU,DTx1200 AU/NZ
Cable certification tester. Tests up to 350MHz; Cat6 Autotest time of 12s.
Comes complete with latest cat6 pM-06 peronality modules. Linkware pC
software, and USb cable. Internal memory stores 350 tests. Optional
memory card stores 2,000 tests.
Fluke DTX1800 Category 7 Cable Certification Tester
FLU,DTx1800 AU/NZ
Cable certification tester up to 900MHz; Cat6 Autotest time of 12s. Comes
complete with latest cat 6 pM-06 personality modules, Linkware pC software,
and USb cable. Internal memory stores 350 tests. Tests to Cat 3, 4, 5, 5E,
6 & 7. Included Cat6 heads will test up to category 6. Optional memory card
stores 2,000 tests.
> NEW
Fluke DTX 10 Gig copper Testing and Certification Kit
FLU,DTx-10G KIT AU
Used in conjunction with the FLU,DTx1800. Enables testing and certification
of twisted pair cabling for 10 Gigabit Ethernet deployments - whether it is an
existing Cat 6 or newly installed augmented Cat 6 cabling system. Measures
the performance for 10 Gig and Alien Crosstalk (ANExT and AFExT) in full
compliance with the industry standards to 500 MHz.
Fluke DTX-MFM Multimode Fibre Adaptor for DTX Cable
Analyser
FLU,DTx-MFM AU
DTx1200/1800 multimode fibre interface. Tests fibre installations in local
area networks. Fits in the slot on the back of DTx cable analyser (standard
copper cable adaptors can be connected but not used simultaneously).
provides fibre testing and certification. bi-directional testing at 850nm
& 1300nm at the same time. Measures optical power loss, length, and
propagation delay for multimode fibres. pass/fail results based on common
fibre standards. SC optical connectors. Includes in built visual fault locater.
(VFL)
Fluke DTX-SFM Singlemode Fibre Adapter for DTX Cable
Analyser
FLU,DTx-SFM AU
DTx1200/1800 singlemode fibre interface. Use for testing fibre installations
in local area networks. Fits in the slot on the back of DTx cable analyser
(standard copper cable adaptors can be connected but not used
simultaneously). provides fibre testing and certification. bi-directional
testing at 1310 nm and 1550 nm at the same time. Measures optical power
loss, length, and propagation delay for multimode fibres. pass/fail results
based on common fibre standards. SC optical connectors. Includes in built
visual fault locater. (VFL)
Fluke DSP Personality Module for DSP4X00 series
FLU,DSp-pM AU
personality module for Fluke DSp4x00 cat6 permanent Link heads. RJ45
connector sets (pM-01, pM-06, pM-25) include 2 modules. block connector
sets include one module (pM-12b, pM-13b). Modules available include pM-
06 (most systems), pM-25 (most unshielded systems), pM-01 (legacy), pM-
12b paduit GIGA-pUNCH 110 block, pM-13b Siemon S210 block.
Fluke Networks CableIQ Cable & Network Identification Tool
FLU,CAbLEIQ
CableIQ cable and network tester for twisted-pair, coax, and audio cabling.
Allows troubleshooting connectivity problems and qualify cabling bandwidth
to see whether an existing cabling link is qualified to support 10/100, VoIp
or Gigabit Ethernet. Discovers what is at the far end of any network cable.
Detects speed and duplex settings of attached switches and PCs. Intelligent
wiremap graphically shows distance to faults (e.g., pin 1 break at 31m). Can
also test cable set-up for audio application (intercom/pA). Hand held and
lightweight, powered by 4 x AA Alkaline batteries. Can be used as a signal
source for optional Intellitone cable tracer.