Instruction Manuals - Cole-Parmer

More documents

Recommendations

Info

<strong>Instruction</strong> Manual pH 1100/ 210010.5.4 Data log setup mode P4.2Use this program select automatic or manual data logging.Automatic data logging can be set at timed intervals from 10seconds to 23 hours, 59 minutes, 59 seconds.1. Enter meter setup mode as described in steps 1-4 in Section10.5.1 Entering meter setup mode (page 50).2. Use Δ/MI key to scroll to program Data Log Setup: P4.2.See Figure 170.3. Press ENTER to enter program Data Log Setup: P4.2.Dat a Log Set up :P4.2Press ENT. to SelectFigure 170Dat a Log:Aut o ManualSel ec t & Pr es s ENTERFigure 1714. Press >/CAL key to toggle between Data Log Auto andManual. The selection will flash. See Figure 171.5. Press ENTER to confirm selection.• If you selected Auto, continue to step 6.• If you select Manual, pressing ENTER returns to the setupmode. Press Δ/MI key to continue to the next setupprogram, or press ∇/MR to go to the previous program.Press EXIT to return to measurement mode.Aut o Dat aLog PeriodHr : 1 Mi n : 3 0 Sec : 0Figure 1726. If you selected Auto in step 5, the display now reads AutoDataLog Period Hr: Min: Sec : Key in the time period(minimum of 10 seconds to maximum of 23 hours, 59 minutes,59 seconds) using the numeric keypad. If you make a mistake,use Δ/MI or ∇/MR keys to highlight mistake, then re-enter.See Figure 172.7. Press ENTER to confirm selection. The screen flashes SysUpdating... Please wait... and then returns to the setup mode.Press Δ/MI key to continue to the next setup program, orpress ∇/MR to go to the previous program. Press EXIT toreturn to measurement mode.10.5.5 Memory recall setup mode P4.3Use this program to select automatic or manual memory recall. Seepage 24 for more information on memory recall.1. Enter meter setup mode as described in steps 1-4 in Section10.5.1 Entering meter setup mode (page 50).2. Use Δ/MI key to scroll to program MemRecall Setup: P4.3.See Figure 173.3. Press ENTER to enter program MemRecall Setup: P4.3.MemRecall Set up:P4.3Press ENT. to SelectFigure 173Me mo r y Rec a l l Mo d eAuto ManualFigure 1744. Press >/CAL key to toggle between Memory Recall ModeAuto and Manual. The selection will flash. See Figure 174.5. Press ENTER to confirm selection and return to the setupmode. Press Δ/MI key to continue to the next setup program,or press ∇/MR to go to the previous program. Press EXIT toreturn to measurement mode.52
<strong>Instruction</strong> Manual pH 1100/ 210010.5.6 Communication setup mode P4.4Use this program to set parameters of serial communication.1. Enter meter setup mode as described in steps 1-4 in Section10.5.1 Entering meter setup mode (page 50).2. Use Δ/MI key to scroll to program Tx/Rx Parameter: P4.4.See Figure 175.3. Press ENTER to enter program Tx/Rx Parameter: P4.4.4. Press >/CALkey to toggle between Baud Rate 4800, 9600 and19200. The selection will flash. See Figure 176. Press ENTERto confirm selection and go to the next setup screen.5. Press >/CALkey to toggle between Stop Bit One and Two.The selection will flash. See Figure 177. Press ENTER toconfirm selection and go to the next setup screen.6. Press >/CALkey to toggle between Parity Bit None, Odd andEven. The selection will flash. See Figure 178.7. Press ENTER to confirm selection and return to the setup mode.Press Δ/MI key to continue to the next setup program, or press∇/MR to go to the previous program. Press EXIT to return tomeasurement mode.Tx/ Rx Parameter:P4.4Press ENT. t o SelectFigure 175Baud Rat e4800 9600 19200Figure 176St op Bit : One TwoFigure 177Par i t y Bi t :None Odd EvenFigure 17810.5.7 Data transfer setup mode P4.51. This program lets you select what data is sent to your printer orcomputer.2. Enter meter setup mode as described in steps 1-4 in Section10.5.1Entering meter setup mode (page 50).3. Use Δ/MI key to scroll to program Data Transfer: P4.5. SeeFigure 179.4. Press ENTER to enter program Data Transfer: P4.5.5. Press >/CALkey to toggle between Data send to printer Currentand Memory. .The selection will flash.See Figure 180.Dat a Tr ansf er :P4.5Press ENT. t o SelectFigure 179Data send to printerCurrent Memor yFigure 1806. Press ENTER to confirm selection and return to the setup mode.Press Δ/MI key to continue to the next setup program, or press∇/MR to go to the previous program. Press EXIT to return tomeasurement mode.53
Page 1: Instruction ManualpH 1100/ pH 2100B
Page 4 and 5: Instruction Manual pH 1100/ 2100TAB
Page 6 and 7: Instruction Manual pH 1100/ 21001 I
Page 8 and 9: Instruction Manual pH 1100/ 21001.3
Page 10 and 11: Instruction Manual pH 1100/ 21002 S
Page 18 and 19: Instruction Manual pH 1100/ 21004 m
Page 20 and 21: Instruction Manual pH 1100/ 21005 I
Page 26 and 27: Instruction Manual pH 1100/ 21009 T
Page 28 and 29: Instruction Manual pH 1100/ 210010.
Page 36 and 37: Instruction Manual pH 1100/ 2100pH
Page 56 and 57: Instruction Manual pH 1100/ 210012
Page 64: For more information on Eutech Inst

Instruction Manuals - Cole-Parmer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?