GM862-GPS Software User Guide - SemiconductorStore.com

More documents

Recommendations

Info

GM862-GPS Software User Guide1vv0300729 Rev. 4 - 24/01/07AT+CBST==1, 0, 0 V.21 300 transparentAT+CBST==2, 0, 0 V.22 1200 transparentAT+CBST==3, 0, 0 V.23 1200/75 transparentAT+CBST==4, 0, 0 V.22Bis 2400 transparentAT+CBST==6, 0, 0 V.32 4800 transparentAT+CBST==7, 0, 0 V.32 9600 transparentAT+CBST==65, 0, 0 V.110 300 transparentAT+CBST==66, 0, 0 V.110 1200 transparentAT+CBST==68, 0, 0 V.110 / X.31 2400 transparentAT+CBST==70, 0, 0 V.110 / X.31 4800 transparentAT+CBST==71, 0, 0 V.110 / X.31 9600 transparentOnce selected the appropriate and parameters from the table:• Send command AT+CBST=,0,• wait for OK response2.7.2 Phone number dialing (data call)2.7.2.1 Dial a given phone number• Send command ATD where: is the phone number to be dialed• wait for response:Response Reason ActionCONNECT 9600The called modem is now on exchange data..line.BUSY The line called is busy retry laterNO ANSWERThe receiver did not answer the retry latercallNO CARRIERThe modem handshaking hasnot been successfulcheck for mobile registrationand signal strength andeventually retry.TIP: The response to the ATD command is returned after the modem handshaking, this takesabout 30 seconds, so allow this time before doing anything.Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 24 of 111
GM862-GPS Software User Guide1vv0300729 Rev. 4 - 24/01/07TIP: When the device is doing the handshake the issue of any character closes the handshakeand aborts the call.For example:1- Let's assume you have to call the national number 040 - 4192111,command:ATD 0404192111responseCONNECT 96002- Let's assume you have to call the national number but in international format +39-40-4192111,command:ATD +39404192111responseCONNECT 96003- Let's assume you have to call the international number +386-40-4192111,command:ATD +386404192111responseCONNECT 96002.7.3 Closing the Data call2.7.3.1 Exit the data mode and enter the command mode• Send escape sequence +++• wait the escape sequence pause time ( see S12 parameter)• wait for response OKNOTE: After the Escape sequence and during the call the only command that is accepted bythe GM862-GPS is the ATH. All the other commands are not supported during a call.TIP: during the escape sequence pause time S12 no further characters should be sent to thedevice in order to enter the command mode.Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 25 of 111
Page 1 and 2: GM862-GPS Software User GuideGM862-
Page 4 and 5: GM862-GPS Software User Guide1vv030
Page 8 and 9: Command Time-Out (Seconds)#SHDN 10#
Page 12 and 13: 2.5.2.3 Provide SIM PIN (only if re
Page 20 and 21: For example:1 - Let's assume that t
Page 30 and 31: +CME ERROR: 17PIN2 is required to c
Page 34 and 35: AT+CPBR=7the response may look like
Page 36 and 37: 3.1.5 Phonebook entry DeleteAs firs
Page 74 and 75:
GM862-GPS Software User Guide1vv030
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
esponse:+CCLK="02/11/07,13:24:47"OK
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
5.6.4 GPS PARAMETERS SAVEGM862-GPS
Page 108 and 109:
Page 110 and 111:
show all

GM862-GPS Software User Guide - SemiconductorStore.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?