eWON General Reference Guide - Esco Drives & Automation

More documents

Recommendations

Info

General Reference GuideIO Servers Configuration5.14.2.2 Global Device AddressThe device address is either appended to the ValueName in the Item Name definition, or entered in the Topic global address fields.The device address syntax is the following:EH[,[[ipaddress,TCP|UDP,port]|[station]][,LUMP]]EH SerialEH,stationEHEH,station,LUMPEH,LUMPstation : address of the PLC on the networkEH,4 the eWON will access PLC number 4.By configuration, an HITACHI PLC could have an undefined station number.If this PLC is alone on a serial link, you don’t need to specify a station number.station : address of the PLC on the networkLUMP : Link Unit Port ModuleEH,4,FFFF0000 the eWON will access PLC number 4 with the LUMP FFFF0000.By configuration, an HITACHI PLC could have an undefined station number.If this PLC is alone on a serial link, you don’t need to specify a station number.LUMP : Link Unit Port ModuleEH,FFFF0000 the eWON will access PLC with the LUMP FFFF0000.EH ethernetEH,ipaddress,TCP|UDP,portEH,ipaddress,TCP|UDP,port,LUMPipaddress : IP address of the PLCTCP|UDP : select the protocol usedport : IP port usedEH,10.0.120.203,TCP,3004 the eWON will access the PLC at 10.0.120.203 with protocolTCP and port 3004ipaddress : IP address of the PLCTCP|UDP : select the protocol usedport : IP port usedLUMP : Link Unit Port ModuleEH,10.0.120.203,TCP,3004,FFFF0000the eWON will access the PLC at 10.0.120.203, protocol TCP, port 3004and LUMP FFFF0000Table 119: HITACHI device address syntaxImportant:If the PLC address is defined at the Topic level, it can be omitted in the Tag definition. In that case the Tag name will only containthe "ValueName".If the PLC address is specified at the Topic level, it will replace any address defined Tag by Tag.RG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 139
General Reference GuideIO Servers Configuration5.15 MITSUBISHI FX IO Server5.15.1 IntroductionThis MITSUFX IOServer allows the eWON to poll tags belonging to a MITSUBISHI FX series PLC using its RS-422 base unit programmingconnector.No remote maintenance functionality is provided by this IO server. The VCOM feature of the eWON has to be used to cover a remotemaintenance.MITSUFX IOServer is available in eWON with Firmware 5.5 and above.5.15.2 Setup5.15.2.1 COM configurationFigure 106: MITSUFX IOServer: COM setupParameterBaud RateParityThe switches of the eWON must be configured in RS485/RS422 mode.DescriptionSpeed of the Serial port.Available speeds are 9600 Bauds or disabledThe parity to apply (None / Even / Odd)Databits The number of bits in data (7 or 8)Stop bit(s) The number of Stop bits (1 or 2)HW modeReply TimeoutChoose the Hardware mode of communication:• Ful Duplex HW handshaking• Full Duplex NO handshaking (by default)• Half duplexThe maximum time the eWON will wait for a valid message responseTable 120: MITSUFX IOServer: COM parametersRG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 140
Page 1 and 2:
eWON Family500, 2001, 4001, 2101, 4
Page 3:
Table of content5.4.3 Tag name conv
Page 6 and 7:
General Reference GuideIntroduction
Page 8 and 9:
General Reference GuideeWON Configu
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
General Reference GuideIO Servers C
Page 88 and 89:
General Reference GuideIO Servers C
Page 90 and 91: General Reference GuideIO Servers C
Page 148 and 149: General Reference GuideMonitoring W
Page 166 and 167: General Reference GuideRetrieving d
Page 168 and 169: General Reference GuideExport Block
Page 190 and 191:
General Reference GuideExport Block
Page 192 and 193:
General Reference GuideExport Block
Page 194 and 195:
General Reference GuideUpgrading th
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
General Reference GuideAppendix10 A
Page 202 and 203:
General Reference GuideAppendix10.5
Page 204 and 205:
Page 206:
show all

eWON General Reference Guide - Esco Drives & Automation

Create successful ePaper yourself

Delete template?

Save as template?