eWON General Reference Guide - Esco Drives & Automation

General Reference GuideeWON ConfigurationExamples:SMS on alarm "SMS Destination" syntax0407886633,ucp,0475161622,proximus0407886633,tap,04751616210407886633,gsm,00407886633,ifz,0Explanationsucp protocol requires the use of a password. In this case, the passwordis "proximus"See in the above table for the word datasize and parity specificationtap protocol does not require to enter a password.See in the above table for the word datasize and parity specificationSyntax for sending an SMS from an eWON with a GSM/GPRS modemNote: we advise you to exclusively use this syntax to send an SMSfrom an eWON that embeds a GSM modem (not tap or ucp protocols).Syntax for sending an SMS to a GSM modem (France)Table 52: SMS destination syntax examplesAll the above strings are valid. Concerning the three last examples in the list, the last "," is not mandatory as there is no password.Important: Password is case sensitive.When defining a phone number with a modem the "," is often used to insert a pause during the dialing operation. As the eWON uses the coma asa separator, the pause dial sign is replaced by a +.For example the 0+0407886633 would dial a 0, then insert a 1 second pause, then dial 0407…The gsm protocol attribute can be used in order to send the SMS directly through the GSM network, not using an SMS server. In this case, thereis no server needed. This is valid only if the eWON embeds a GSM or GPRS modem.BENELUX only: SEMASCRIPTIt is possible to send Semascript/ SemaDigit to a Semaphone inside of the Benelux area, by using the Belgacom server.Example:You want to send a semadigit to number 0498373101...You must call the server at phone number 0458500001 (0+0458500001 if you must first dial a 0 and wait a pause)Keep only the last 7 digits of the semaphone destination number, and use TAP protocol with "7e1":sendsms "8373101,tap7e1,0458500001","0498373101"if eWON is behind a PABX and 0 must be dialed first use:sendsms "8373101,tap7e1,0+0458500001","0498373101"FRANCE only: ALPHAPAGEAs for SEMASCRIPT, it is possible to send ALPHAPAGE messages to ALPHAPAGE pagers in France, by using the emessage server: the serveris managed by a German firm called emessage, (http://www.emessage.de/en/index.html). As for the SEMASCRIPT users, the ALPHAPAGEusers have chosen to keep on using a pager, with which the broadcasting coverage is better than with the GSM network (the users are sure toreceive the message, that is not always the case with SMS).The used protocol is TAP. The operating mode is the same as for SEMASCRIPT:You want to send an ALPHAPAGE message to number 0612345678...You must call the server at phone number 0836601212 (0+0836601212 if you must first dial a 0 and wait a pause)Keep only the last 7 digits of the alphapage destination number, and use TAP protocol with "7e":sendms “2345678,tap7e,0836601212”if eWON is behind a PABX and 0 must be dialed first use:sendms “2345678,tap7e,0+0836601212”See also:The BASIC function SENDSMS and SENDMAIL in the “eWON Programming Manual”.3.4.2.2.3 FTP on alarm configurationAlarm action PropertiesPut FTP uponDestination file nameFile contentDescriptionChecks the alarm states triggering the Put FTP (ALM, ACK, RTN, END)Name of the file to create on the FTP server. The name can contain path specification.The file content can be static or dynamic (see below)Table 53: alarm action propertiesRG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 78