eWON General Reference Guide - Esco Drives & Automation

More documents

Recommendations

Info

General Reference GuideIO Servers Configuration5.2.4 Standard IO server configuration pageWhen no dedicated configuration page is defined for configuring an IO server, the standard configuration page is used.Figure 73: Standard IO server configuration pageAs you can see in the above example, the standard configuration screen is a simple text edition area. Each parameter is entered on a separateline, the parameter value is separated from the parameter name by a colon ':' .The generic format of a line is:PARAM_NAME:PARAM_VALUEWarning: Extra space must be removed.When using this configuration, you must respect the correct syntax of each parameter and the values for each parameter.The list of valid parameters and their corresponding valid values are listed in the corresponding IO server documentation (see following chapters).Any error that would occur when the eWON applies the configuration that you have entered would be written to the event file. Please refer tochapter “Files transfer” on page 154 to see how to get access to the events file.RG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 87
General Reference GuideIO Servers Configuration5.3 Modbus IO server5.3.1 IntroductionThe MODBUS IO Server setup is the standard remote IO communication setup of the eWON. It is used to configure:• The eWON as a Modbus RTU master.• The eWON as a Modbus TCP slave and master.The first feature (Modbus TCP slave) is specific to the MODBUS IO server; it is actually designed to provide access to eWON Tag values and,unlike all the other IO servers, for interfacing field values with the eWON.The second feature (MODBUS Master) is the actual IO server feature that provides an interface to the field values as a common IO server.The eWON MODBUS IO server will give access to values in equipments having a MODBUS interface.The interface can be:• RS485 – MODBUS RTU protocol will be used• ETHERNET/PPP – MODBUS TCP protocol will be used.The eWON can mix access to MODBUS RTU and MODBUS TCP, depending on the way the Tag address is defined.5.3.2 Setup5.3.2.1 Setup for eWON ServerFigure 74: Modbus TCP Server configurationThis page defines the eWON configuration when used as a Modbus TCP slave.As described in the Tag configuration paragraph, each Tag can be published to Modbus TCP so that a Modbus TCP can read their values.This setup screen defines the eWON address, and globally enables or disables the Modbus TCP slave feature.eWON Server PropertieseWON server enabledModbus TCP Unit addressDescriptionGlobally enables or disables the Modbus TCP Server feature. If disabled, then any requestfrom a Modbus TCP master will be rejected, even if Tags are published.This feature is used by some gateway but can usually be left to 1 because Modbus TCPappears as a point to point connection.Table 56: eWON server configuration - eWON as Modbus TCP slave5.3.2.2 Setup for eWON IO server and Gateway - COM SetupFigure 75: Modbus communications configurationIf more than one Serial port are available, you must choose on which COM the modbus request will be sent.This configuration part defines the RS485 setup. The four first fields are used to define the baud rate, parity, number of stop bits and the replytimeout (in msec – usually 1000 msec).Warning: When there are multiple IO servers using potentially the serial line, then the unused IO server must be Cleared or thebaudrate must be set to Disabled.RG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 88
Page 1 and 2:
eWON Family500, 2001, 4001, 2101, 4
Page 3:
Table of content5.4.3 Tag name conv
Page 6 and 7:
General Reference GuideIntroduction
Page 8 and 9:
General Reference GuideeWON Configu
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39: General Reference GuideeWON Configu
Page 86 and 87: General Reference GuideIO Servers C
Page 138 and 139:
General Reference GuideIO Servers C
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
General Reference GuideMonitoring W
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
General Reference GuideRetrieving d
Page 168 and 169:
General Reference GuideExport Block
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
General Reference GuideUpgrading th
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
General Reference GuideAppendix10 A
Page 202 and 203:
General Reference GuideAppendix10.5
Page 204 and 205:
Page 206:
show all

eWON General Reference Guide - Esco Drives & Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?