eWON General Reference Guide - Esco Drives & Automation

More documents

Recommendations

Info

General Reference GuideeWON Configuration3.3.4.2.2 Modem Incoming & OutgoingWarning: Depending on the eWON's version (c.f. Table 187 on page 203)This group contains the PPP(Point to Point) setup of the eWON that sets up the PPP settings for the server and client functions of the eWONengine.3.3.4.2.2.1 IncomingFigure 30: Modem Incoming setup pageControleWON PPP server IP addressPPP client IP addressEnable protocol compressionUse incoming for outgoingNumber of rings before modemanswersIdle time before hanging upReset eWON if no incomingconnection after ...DescriptionPPP server Internet protocol (IP) address of the eWON. Use this IP address to connect to the eWONusing a RAS connection. These are 4 numbers from 0 to 255 separated by a dot.Type the IP address that the eWON will allocate to the RAS client to establish the communication.Enables the compression negotiation request when an incoming call occurs. This includes all thecompression modes known by the eWON PPP engine (Van Jacobson, header compression,…).When checked, this ensures that when an incoming call is undergoing, no external event, such asalarm Email, will drop the line in order to initiate a new connection. If an alarm has to be sent throughthe PPP connection (FTP, Email, …), the current PPP link will be used. Be aware that SMS alarms willalways drop the line, whatever the value of this checkbox. On the other hand, if this box is uncheckedand an Email has to be sent while the connection has been established by a user to browse theeWON, if the Email can be sent through the Ethernet link, the PPP link will NOT be dropped.note: See also “Ethernet Gateway behavior” on page 49You can fix the number of rings before the eWON answers. Default value is 0.After this amount of time without data transfer on the PPP link between the eWON (any type of PPPpacket) and a remote host (Computer).Consider this parameter like a Watchdog parameter. To avoid eWON to stay stucked due to anymodem reason or other, you can use this parameter to force an eWON to reboot if no incomingconnection was performed after xxx Hours since the last connection.Table 29: Modem Incoming controlsRG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 37
General Reference GuideeWON Configuration3.3.4.2.2.2 OutgoingGlobal parametersFigure 31: Modem Outgoing Global setup pageControlDial and connection timeoutEnable compressionDelay between dialout retriesIdle time before hanging upMax outgoing call durationHang up if no outgoing actionafterSelect next server in case oferrorDescriptionTime allowed for the whole establishment of the PPP link to be up. This means modem call,modem negotiation, PPP negotiation and logon. This time includes all trials on each server.This is thus a global time.Enable the compression negotiation request when an outgoing call occurs. This includes allcompression modes known by the eWON PPP engine (Van Jacobson, headercompression,…).In case of an unsuccessful attempt to establish the outgoing communication, then eWON willretry to establish it again. This parameter will allow you to define the amount of time theeWON will wait to try and establish again the outgoing action.eWON will hang up after this amount of time if no data transfer occurs on the PPP linkbetween the eWON (any type of PPP packet) and a remote host (Computer).The maximum amount of time of the outgoing call. When this amount of time is reached, thenthe eWON stops the PPP communication.When a PPP link is triggered by an outgoing action (not by DialOnDemand), you can force theinterruption of the line immediately after the actions (set 0) or let the PPP active for an amountof time (set >0). The PPP link will be shut down after the x minutes even if transfers are inprogress.The Idle time before hanging up is always active.When the call to a server failed, you can choose the behavior of the next call.eWON will be configured to:• Use last valid server• Always return to server 1• Use only server 1• Use only server 2Table 30: outgoing calls configuration controlsRG-001-0-EN ver 1.5 eWON® - 20/03/2009 - ©ACT'L sa Page 38
Page 1 and 2: eWON Family500, 2001, 4001, 2101, 4
Page 3: Table of content5.4.3 Tag name conv
Page 6 and 7: General Reference GuideIntroduction
Page 8 and 9: General Reference GuideeWON Configu
Page 86 and 87: General Reference GuideIO Servers C
Page 88 and 89:
General Reference GuideIO Servers C
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
General Reference GuideMonitoring W
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
General Reference GuideRetrieving d
Page 168 and 169:
General Reference GuideExport Block
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
General Reference GuideUpgrading th
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
General Reference GuideAppendix10 A
Page 202 and 203:
General Reference GuideAppendix10.5
Page 204 and 205:
Page 206:
show all

eWON General Reference Guide - Esco Drives & Automation

Create successful ePaper yourself

Delete template?

Save as template?