No320S Owner's Manual - Mark Levinson

More documents

Recommendations

Info

Controls & Modes<strong>Mark</strong> <strong>Levinson</strong>Balance (continued)The balance control facilitates precise adjustments in 0.1dBincrements between 0.1 and 20.0dB. When the balance offsetexceeds 20.0dB, the Nº 320S mutes the channel outputting thelower signal level.To adjust the left-to-right channel balance of the main outputconnectors:1. Press and release the front panel or remote control balancebutton to open the balance control on the front panel displayas shown to the left.• The front panel balance LED lights red to indicate thatthe balance control is open.4-42. Rotate the front panel volume knob or press the remotecontrol volume ± buttons to make the desired adjustments.• Rotate the volume knob clockwise or press the volume +button to decrease the output level of the left channel.The balance control appears as shown to the left to indicatethat balance is offset in favor of the right channel.• Rotate the volume knob counterclockwise or press thevolume – button to decrease the output level of the rightchannel. The balance control appears as shown to the leftto indicate that balance is offset in favor of the leftchannel.• Select the 0.0 setting to balance the output levels of theleft and right channels, allowing both channels to outputat the same level. The balance control appears as shownto the left to indicate that balance is centered between theleft and right channels.3. When the desired adjustments have been made, press andrelease the balance button to close the balance control.• Otherwise, the balance control automatically closes a fewseconds after the last command is received. If this occurs,the selected setting is automatically applied.• The front panel balance LED remains lit if the left-to-rightchannel balance of the main output connectors is offset.NoteAll Nº 320S volume controls, including master volume andbalance, are deactivated when SSP mode (page 4-8) isactivated.
Nº 320S Controls & ModesMono PlaybackSends mono (rather than stereo) signals to the main outputconnectors, whether those signals are using the balanced (XLR) orsingle-ended (RCA) main output connectors. The mono playbackcontrol has no affect on the record output connectors.To toggle between mono and stereo playback:Press and release the remote control mono button.• During stereo playback, pressing and releasing the monobutton activates the selected mode of mono playback. Thefront panel mono LED lights red to indicate that monoplayback is activated.• During mono playback, pressing and releasing the monobutton deactivates mono playback and activates to stereoplayback.MODEL + R, L ONLY, R ONLY, L – RDetermines the mode of mono playback that is activated whenthe remote control mono button is pressed. The factory-defaultMODE parameter setting is L + R.• Selecting the L + R mono mode sends an equal combinationof left and right-channel input signals to the left and rightchannelmain output connectors. Refer to L + R BalanceControl Tip (next page) for additional information.• Selecting the L ONLY mono mode sends the left-channel inputsignal to the left and right-channel main output connectors.The right-channel input signal is ignored.• Selecting the R ONLY mono mode sends the right-channel inputsignal to the left and right-channel main output connectors.The left-channel input signal is ignored.• Selecting the L – R mono mode sends the difference betweenthe left and right-channel input signals to the left and rightchannelmain output connectors. Refer to L – R PhonoAlignment Tip (page 4-7) for additional information.4-5MODE: L + RTo select the desired mono mode:1. Press and hold the remote control mono button until theMODE parameter opens on the front panel display as shownto the left.2. Press and release the mono button to cycle through allavailable MODE parameter settings.(continued)
Page 2 and 3: Important Safety InstructionsRead a
Page 4 and 5: IntroductionMark LevinsonTable of C
Page 6 and 7: IntroductionMark LevinsonDocumentat
Page 8 and 9: Getting StartedMark LevinsonSpecial
Page 10 and 11: Getting StartedMark LevinsonHighlig
Page 12 and 13: Getting StartedMark LevinsonPlaceme
Page 14 and 15: Getting StartedMark LevinsonWarm-Up
Page 16 and 17: Getting StartedMark LevinsonQuick S
Page 18 and 19: Basic OperationMark LevinsonFront P
Page 20 and 21: Basic OperationMark LevinsonFront P
Page 22 and 23: Basic OperationMark LevinsonRear Pa
Page 24 and 25: Basic OperationMark LevinsonRear Pa
Page 26 and 27: Basic OperationMark LevinsonMaking
Page 28: Basic OperationMark LevinsonCreatin
Page 31 and 32: Nº 320S Basic OperationNoteThe Nº
Page 33 and 34: Nº 320S Basic Operation4. enter bu
Page 35 and 36: Nº 320S Basic OperationThe Mute pa
Page 37 and 38: Setup MenuMark LevinsonNavigating t
Page 39 and 40: Setup MenuMark LevinsonSet Inputs M
Page 41 and 42: Setup MenuMark LevinsonCharacter Li
Page 43 and 44: Setup MenuMark LevinsonRec.OutNONE,
Page 45 and 46: Setup MenuMark LevinsonTeach IR Men
Page 47 and 48: 4Controls & ModesStandbyAllows the
Page 49: Nº 320S Controls & ModesTo adjust
Page 53 and 54: Nº 320S Controls & Modes8. When th
Page 55 and 56: Nº 320S Controls & ModesTo activat
Page 57 and 58: 5Troubleshooting & MaintenanceTroub
Page 59 and 60: Nº 320S Troubleshooting & Maintena
Page 61 and 62: Nº 320S Troubleshooting & Maintena
Page 63 and 64: AppendixMark LevinsonSpecifications
Page 65 and 66: AppendixMark Levinson(continued)Ins
Page 67 and 68: IndexMark LevinsonIndex (continued)
Page 69 and 70: IndexMark LevinsonIndex (continued)
Page 71 and 72: Obtaining ServiceWe take great prid

No320S Owner's Manual - Mark Levinson

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?