USER’S MANUAL

More documents

Recommendations

Info

Energy [733] Displays the total energy consumption since the last energy reset [7331] took place. Unit: Range: kWh 0.0–999999kWh Communication information Modbus Instance no/DeviceNet no: 31034 Profibus slot/index 121/178 Fieldbus format Modbus format Reset Energy [7331] Resets the kWh counter. The stored information will be erased and a new registration period will start. Default: Selection: No No, Yes Communication information Modbus Instance no/DeviceNet no: 6 Long, 1=1 W EInt Profibus slot/index 0/5 Fieldbus format Modbus format 733 Energy Stp UInt UInt kWh 7331 Rst Energy Stp No NOTE: After reset the setting automatically goes back to “No”. 11.8 View Trip Log [800] Main menu with parameters for viewing all the logged trip data. In total the VSD saves the last 10 trips in the trip memory. The trip memory refreshes on the FIFO principle (First In, First Out). Every trip in the memory is logged on the time of the Run Time [731] counter. At every trip, the actual values of several parameter are stored and available for troubleshooting. 11.8.1 Trip Message log [810] Display the cause of the trip and what time that it occurred. When a trip occurs the status menus are copied to the trip message log. There are nine trip message logs [810]–[890]. When the tenth trip occurs the oldest trip will disappear. Unit: Range: h: m (hours: minutes) 0h: 0m–65355h: 59m For fieldbus integer value of trip message, see message table for warnings, [722]. NOTE: Bits 0–5 used for trip message value. Bits 6–15 for internal use. Communication information Modbus Instance no/DeviceNet no: 31101 Profibus slot/index 121/245 Fieldbus format Modbus format 8x0 Trip message Stp h:mm:ss 810 Ext Trip Stp 132:12:14 UInt UInt Trip message [811]-[81N] The information from the status menus are copied to the trip message log when a trip occurs. Trip menu Copied from Description 811 711 Process Value 812 712 Speed 813 712 Torque 814 714 Shaft Power 815 715 Electrical Power 816 716 Current 817 717 Output voltage 818 718 Frequency 819 719 DC Link voltage 81A 71A Heatsink Temperature 81B 71B PT100_1, 2, 3 81C 721 VSD Status 81D 723 Digital input status 81E 724 Digital output status 81F 725 Analogue input status 1-2 81G 726 Analogue input status 3-4 81H 727 Analogue output status 1-2 146 Functional Description Omron SX inverter manual
Trip menu Copied from Description 81I 728 I/O status option board 1 81J 729 I/O status option board 2 81K 72A I/O status option board 3 81L 731 Run Time 81M 732 Mains Time 81N 733 Energy 81O 310 Process reference Communication information Modbus Instance no/DeviceNet no: 31102 - 31135 Profibus slot/index Fieldbus format Modbus format Example: Fig. 98 shows the third trip memory menu [830]: Over temperature trip occurred after 1396 hours and 13 minutes in Run time. Fig. 98 Trip 3 121/246 - 254, 122/0 - 24 Depends on parameter, see respective parameter. Depends on parameter, see respective parameter. 830 Over temp Stp 1396h:13m 11.8.2 Trip Messages [820] - [890] Same information as for menu [810]. Communication information Modbus Instance no/ DeviceNet no: Profibus slot/index Fieldbus format Modbus format 31151–31185 31201–31235 31251–31285 31301–31335 31351–31385 31401–31435 31451–31485 31501–31535 122/40–122/74 122/90–122/124 122/140–122/174 122/190–122/224 122/240–123/18 123/35 - 123/68 123/85–123/118 123/135–123/168 Trip log list 2 3 4 5 6 7 8 9 Trip log list 2 3 4 5 6 7 8 9 Depends on parameter, see respective parameter. Depends on parameter, see respective parameter. All nine alarm lists contain the same type of data. For example DeviceNet parameter 31101 in alarm list 1 contains the same data information as 31151 in alarm list 2. It is possible to read all parameters in alarm lists 2–9 by recalculating the DeviceNet instance number into a Profibus slot/index number. This is done in the following way: slot no = abs((dev instance no-1)/255) index no = (dev instance no-1) modulo 255 dev instance no = slot nox255+index no+1 Example: We want to read out the process value out from alarm list 9. In alarm list 1 process value has the DeviceNet instance number 31102. In alarm list 9 it has DeviceNet instance no 31502 (see table 2 above). The corresponding slot/index no is then: slot no = abs((31502-1)/255)=123 index no (modulo)= the remainder of the division above = 136, calculated as: (31502-1)-123x255=136 11.8.3 Reset Trip Log [8A0] Resets the content of the 10 trip memories. 8A0 Reset Trip Stp No Default: No 0 Yes 1 No Omron SX inverter manual Functional Description 147
Page 1 and 2:
Cat. No. I127-EN-00B SX-V High powe
Page 4 and 5:
Safety Instructions Precautions sev
Page 6 and 7:
Precautions to be taken with a conn
Page 8 and 9:
Contents 1. Introduction ..........
Page 10 and 11:
1. Introduction Omron SX-V is used
Page 12 and 13:
Category C2: Power Drive System (PD
Page 14 and 15:
2. Mounting This chapter describes
Page 16 and 17:
2.2.2 Mounting schemes Membrane cab
Page 18 and 19:
2330 2330 1000 600 1200 600 Fig. 11
Page 20 and 21:
3. Installation The description of
Page 22 and 23:
RFI-Filter Mains VSD maintenance sw
Page 24 and 25:
3.5.2 Tightening torque for mains a
Page 26 and 27:
4. Getting Started This chapter is
Page 28 and 29:
6. Set motor power [223]. 7. Set mo
Page 30 and 31:
5. Control Connections 5.1 Control
Page 32 and 33:
5.4 Connection example Fig. 24 give
Page 34 and 35:
angle. Do not let the signal cable
Page 36 and 37:
6. Applications This chapter contai
Page 38 and 39:
7. Main Features This chapter conta
Page 40 and 41:
One motor must stop before changing
Page 42 and 43:
Stop RunL RunR Enable Reset +24 V X
Page 44 and 45:
Torque [%] [4161] MaxAlarmMar (15%)
Page 46 and 47:
7.6.2 Fixed MASTER This is the defa
Page 48 and 49:
7.6.6 PID control When using the Pu
Page 50 and 51:
7.6.8 Checklist And Tips 1. Main Fu
Page 52 and 53:
Stopping an additional pump This fi
Page 54 and 55:
46 EMC and Machine Directive Omron
Page 56 and 57:
alarm messages. 300 Process Appl St
Page 58 and 59:
The VSD will be started and stopped
Page 60 and 61:
100 0rpm Stp A 0.0A Menu 100 appear
Page 62 and 63:
Motor M2 44041-44048 172/180 to 174
Page 64 and 65:
Programming example: typedef struct
Page 66 and 67:
58 Serial communication Omron SX in
Page 68 and 69:
11.1.2 2nd Line [120] Sets the cont
Page 70 and 71:
Local/Remote key function [217] The
Page 72 and 73:
11.2.4 Motor Data [220] In this men
Page 74 and 75:
When the motor has no cooling fan,
Page 76 and 77:
PWM Mode [22E2] Default: Standard S
Page 78 and 79:
Menu [234] PTC contains functions t
Page 80 and 81:
The active set can be viewed with f
Page 82 and 83:
Number of Trips [251] Any number se
Page 84 and 85:
Communication information Modbus In
Page 86 and 87:
Min Alarm [25K] Delay time starts c
Page 88 and 89:
Modbus format UInt Brake Fault [25V
Page 90 and 91:
Communication Fault Time [2642]] De
Page 92 and 93:
Default: Speed F(AnIn) 0 Function o
Page 94 and 95:
Fieldbus format Long, 1=0.001 Modbu
Page 96 and 97:
pm 333 Acc MotPot Stp 16.0s A Nom.
Page 98 and 99:
Deceleration Ramp Type [338] Sets t
Page 100 and 101:
Default: Range: Depend on: 0 rpm -
Page 102 and 103:
Fieldbus format Modbus format PID r
Page 104 and 105: Profibus slot/index 169/32 Fieldbus
Page 106 and 107: n [367] Preset Ref 6, with default
Page 108 and 109: PID sleep functionality This functi
Page 110 and 111: 11.3.9 Pump/Fan Control [390] The P
Page 112 and 113: Change Timer [395] When the time se
Page 114 and 115: Lower Band Limit [39C] If the speed
Page 116 and 117: Run Times 1-6 [39H] to [39M] Unit:
Page 118 and 119: Max Alarm [416] Max Alarm Margin [4
Page 120 and 121: The default set levels for the (pre
Page 122 and 123: Overvolt control [424] Used to swit
Page 124 and 125: User Bipol mA 3 0-10V 4 2-10V 5 Use
Page 126 and 127: Communication information Modbus In
Page 130 and 131: Profibus slot/index 169/145 Fieldbu
Page 132 and 133: AnOut1 Advanced [533] With the func
Page 136 and 137: Digital Out 2 [542] Relay 2 [552] N
Page 138 and 139: Virtual Connection 1 Source [562] W
Page 140 and 141: Communication information No. 1 2 3
Page 144 and 145: Y Operator 2 [624] Selects the seco
Page 146 and 147: Timer 1 Mode [642] Default: Off 0 D
Page 148 and 149: Timer 2 T2 [655] Default: 0:00:00,
Page 150 and 151: DC Link Voltage [719] Displays the
Page 152 and 153: The example in Fig. 94 indicates th
Page 158 and 159: 150 Functional Description Omron SX
Page 166 and 167: 12.2 Trip conditions, causes and re
Page 168 and 169: Table 28 Trip condition, their poss
Page 170 and 171: Check external wiring, connections
Page 172 and 173: Table 30 Brake resistor SX-V 400V t
Page 174 and 175: When the "Safe Stop" condition is a
Page 176 and 177: 168 Options Omron SX inverter manua
Page 178 and 179: Table 35 Typical motor power at mai
Page 180 and 181: 14.3 Operation at higher temperatur
Page 182 and 183: 14.6 Environmental conditions Table
Page 184 and 185: 176 Technical Data Omron SX inverte
Page 186 and 187: Table 46 Type cables cross-sections
Page 188 and 189: 180 Technical Data Omron SX inverte
Page 190 and 191: DEFAULT CUSTOM DEFAULT CUSTOM 2651
Page 192 and 193: DEFAULT CUSTOM DEFAULT CUSTOM 5197
Page 194 and 195: DEFAULT CUSTOM DEFAULT CUSTOM 81I I
Page 196 and 197: 89E DEFAULT DigOut status 89F AnIn
Page 198 and 199: External Control Panel ............
Page 200 and 201: (413) .............................
Page 202: T Terminal connections ............
show all

USER’S MANUAL

Create successful ePaper yourself

Delete template?

Save as template?